CNC 8055 - Operating manual (MC option) - Fagor Automation

More documents

Recommendations

Info

3. WORKING WITH OPERATIONS OR CYCLES Profile milling operation CNC 8055 CNC 8055i ·MC· OPTION SOFT: V01.3X ·82· 3.3.2 Profile definition (level 2) Defining the profile program. Operating manual The profile program may be defined as follows. Key in the profile program number directly. If the "profile program" is known, key in the program number and press [ENTER]. Access the "profile programs" to select one of them. Press the [] key. The canned cycle will show a window with the profile programs currently defined. Use the [] and [] keys to move around this window. After positioning the cursor on the desired program, press [ENTER]. To exit this window without selecting any program, use the [] y [] keys. i The profile programs can also be accessed in the "M" mode because the CNC saves them internally as P997xxx. Example: Profile program 123 is internally saved as P997123. When saving a part-program that contains a level-2 profile cycle into an external device, PC, floppy drive, etc. also save its associated profile program P997xxx. Editing a new profile program. To edit a new profile program, key in the program number (between 0 and 999) and press [RECALL]. The CNC will show the window for the profile editor (see operating manual). Once the profile has been edited, the CNC requests the comment to be associated with the profile program being edited. Enter the desired comment and press [ENTER]. If no comment is desired, press [ESC]. Copying a profile program. Press the [] key. The canned cycle will show the profile programs currently defined. Place the cursor on the profile program to be copied and press [P.PROG]. The CNC requests the number of the new profile and it allows changing its comment. If the number entered is the same as that of an existing profile, the CNC requests confirmation to replace it. Modifying an existing profile program. To modify a profile program, key in the program number and press [RECALL]. The CNC will show, in the window for the profile editor, the profile that is currently defined. With this profile, the following actions are possible: Adding new elements at the end of the current profile. Modifying the data of any element. Modifying or including chamfers, rounding, etc. Deleting elements of the profile. Deleting an existing profile program. Press the [] key. The canned cycle will show the profile programs currently defined. Place the cursor on the profile program to be deleted and press [CLEAR]. The CNC requests confirmation.
Operating manual 3.4 Surface milling and slot milling operations This key accesses the surface milling and slot milling operations. Surface milling operation. The following data must be defined: The type of surface milling, the starting point (X1, Y1), the dimensions of the surface milling (L, H, E, ) and the machining conditions in Z (Zs, Z, P, I, Fz). Also, you must define the milling pass () in the data area for the roughing operation and the finishing stock (z) in the data area for the finishing operation. Grooving operation. The following data must be defined: The type of slot milling, the starting point (X1, Y1), the dimensions of the slot (L, H, E, ) and the machining conditions in Z (Zs, Z, P, I, Fz). In the roughing area, define the milling pass () and the machining direction. In the finishing area, define the finishing stocks ( and z), the number of finishing passes and the machining direction. 3. WORKING WITH OPERATIONS OR CYCLES Surface milling and slot milling operations CNC 8055 CNC 8055i ·MC· OPTION SOFT: V01.3X ·83·
Page 1 and 2:
CNC 8055 ·MC· Operating manual Re
Page 3 and 4:
Operating manual INDEX About the pr
Page 5 and 6:
ABOUT THE PRODUCT BASIC CHARACTERIS
Page 7:
DECLARATION OF CONFORMITY The manuf
Page 10 and 11:
CNC 8055 CNC 8055i ·10· Version h
Page 12 and 13:
CNC 8055 CNC 8055i ·12· Safety co
Page 14 and 15:
CNC 8055 CNC 8055i ·14· Safety co
Page 16 and 17:
CNC 8055 CNC 8055i ·16· Warranty
Page 18 and 19:
CNC 8055 CNC 8055i ·18· Material
Page 20 and 21:
CNC 8055 CNC 8055i ·20· Additiona
Page 22 and 23:
CNC 8055 CNC 8055i ·22· Fagor doc
Page 24 and 25:
1. GENERAL CONCEPTS Keyboard CNC 80
Page 26 and 27:
1. GENERAL CONCEPTS General concept
Page 28 and 29:
1. GENERAL CONCEPTS General concept
Page 30 and 31:
1. GENERAL CONCEPTS CNC 8055 CNC 80
Page 32 and 33: 2. OPERATING IN JOG MODE Introducti
Page 40 and 41: 2. OPERATING IN JOG MODE Home searc
Page 42 and 43: 2. OPERATING IN JOG MODE Jog moveme
Page 50 and 51: 2. OPERATING IN JOG MODE Tool contr
Page 52 and 53: 2. OPERATING IN JOG MODE Tool contr
Page 54 and 55: 2. OPERATING IN JOG MODE Tool calib
Page 68 and 69: 2. OPERATING IN JOG MODE CNC 8055 C
Page 70 and 71: 2. OPERATING IN JOG MODE ISO manage
Page 72 and 73: 3. WORKING WITH OPERATIONS OR CYCLE
Page 128 and 129: 4. OPERATING IN ISO MODE CNC 8055 C
Page 130 and 131: 4. OPERATING IN ISO MODE CNC 8055 C
Page 132 and 133:
4. OPERATING IN ISO MODE Programmin
Page 134 and 135:
5. SAVING PROGRAMS CNC 8055 CNC 805
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
6. EXECUTION AND SIMULATION CNC 805
Page 150 and 151:
6. EXECUTION AND SIMULATION CNC 805
Page 152 and 153:
6. EXECUTION AND SIMULATION Executi
Page 154 and 155:
6. EXECUTION AND SIMULATION Graphic
Page 156 and 157:
6. EXECUTION AND SIMULATION Graphic
Page 158:
6. CNC 8055 CNC 8055i ·MC· OPTION
show all

CNC 8055 - Operating manual (MC option) - Fagor Automation

Create successful ePaper yourself

Delete template?

Save as template?