EN: man_8065_chn.pdf - Fagor Automation

More documents

Recommendations

Info

6. PROGRAMMING IN A SYSTEM WITH CHANNELS. Communication and synchronization. CNC 8065 (REF: 1103) ·112· Execution channels
MULTI-SPINDLE SYSTEM. SPINDLE CONTROL. 7 The CNC can have up to four spindles distributed between the various channels of the system. A channel may have one, several or no spindles associated with it. Via part-program or in MDI/MDA mode, it is possible to indicate which spindle the commands are directed to; when not indicated, the commands are directed to the master spindle of the channel. Each channel can only control its spindles; it is not possible to start up or stop the spindles of another channel directly. Indirectly, the CNC can control the spindles of another channel using the instruction #EXBLK. Multi-spindle system. A multi-spindle channel is one that has two or more spindles. Via part-program or MDI, it is possible to indicate which spindle the commands are directed to; when not indicated, the commands are directed to the master spindle of the channel. All the spindles of the channel may be running at the same time. Also, each of them may be in a different mode; turn in different directions, be in positioning mode, etc. Master spindle of the channel. The master spindle is the main spindle of the channel. In general, whenever a channel has a single spindle, it will be its master spindle. When a channel has several spindles, the CNC will choose the master spindle according to the established criteria. CNC 8065 (REF: 1103) ·113·
Page 1 and 2:
CNC 8065 Execution channels (Ref: 1
Page 3 and 4:
Execution channels CHAPTER 1 INTROD
Page 5 and 6:
Execution channels ABOUT THE PRODUC
Page 7:
Execution channels Software options
Page 11:
Execution channels VERSION HISTORY
Page 14 and 15:
CNC 8065 (REF: 1103) ·14· PRECAUT
Page 17 and 18:
Execution channels WARRANTY TERMS I
Page 19:
Execution channels MATERIAL RETURNI
Page 23 and 24:
INTRODUCTION. 1 This manual is dire
Page 25 and 26:
Execution channels A permanent chan
Page 27:
CONFIGURATION I
Page 30 and 31:
2. SETTING A MULTI-CHANNEL SYSTEM.
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
3. LOGIC CNC INPUTS AND OUTPUTS. CN
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63: 3. LOGIC CNC INPUTS AND OUTPUTS. CN
Page 70 and 71: 4. CNC-PLC COMMUNICATION. CNC 8065
Page 81 and 82: OPERATION AND INTERFACE. 5 The chan
Page 83 and 84: Execution channels Messages active
Page 85 and 86: Execution channels 5.3 Channel sync
Page 87 and 88: PROGRAMMING IN A SYSTEM WITH CHANNE
Page 89 and 90: Execution channels 6.2 Executing a
Page 91 and 92: Execution channels 6.3.1 Set a new
Page 93 and 94: Execution channels 6.3.2 Add a new
Page 95 and 96: Execution channels 6.3.3 Remove an
Page 97 and 98: Execution channels Accessing the va
Page 99 and 100: Execution channels 6.3.6 Variables
Page 101 and 102: Execution channels 6.4.1 Set a new
Page 103 and 104: Execution channels 6.4.3 Remove a s
Page 105 and 106: Execution channels 6.4.5 Cancel the
Page 107 and 108: Execution channels 6.5 Communicatio
Page 109 and 110: Execution channels 6.5.2 Synchroniz
Page 111: Execution channels 6.5.3 Variables
Page 115 and 116: Execution channels If two or more s
Page 117 and 118: Execution channels 7.2 Spindle spee
Page 121 and 122: Execution channels SPINDLE SPEED IN
Page 123 and 124: Execution channels 7.4 G192. Turnin
Page 125 and 126: Execution channels 7.5 M03/M04/M05.
Page 127 and 128: Execution channels 7.6 M41-M44. Gea
Page 129 and 130: Execution channels 7.7 M19. Spindle
Page 133 and 134: Execution channels ·sn· Name, log
Page 135 and 136: Execution channels CNC 8065 (REF: 1
show all

EN: man_8065_chn.pdf - Fagor Automation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?