EN: man_8065_chn.pdf - Fagor Automation

More documents

Recommendations

Info

7. MULTI-SPINDLE SYSTEM. SPINDLE CONTROL. CNC <strong>8065</strong> (REF: 1103) ·122· G96/G97. Turning speed or constant surface speed. (V.)[ch].A.PRGCSS.sn (V.)[ch].SP.PRGCSS.sn Variable that can only be read from the program, PLC and interface. The variable returns the value of block preparation. Channel [ch]. Speed active by program for G96. Execution channels Being G96 active, programming a new speed in MDI mode updates the value of this variable. Syntax. ·ch· Channel number. ·sn· Name, logic number or index of the spindle. V.A.PRGCSS.S Spindle S. V.SP.PRGCSS.S Spindle S. V.SP.PRGCSS Master spindle. V.A.PRGCSS.5 Spindle with logic number ·5·. V.SP.PRGCSS.2 Spindle with index ·2· in the system. V.[2].SP.PRGCSS.1 Spindle with index ·1· in the channel ·2·.
Execution channels 7.4 G192. Turning speed limit. Function G192 limits the spindle turning speed in both work modes; G96 and G97. This function is especially useful when working at constant cutting speed while machining large parts or when doing spindle maintenance work. If function G192 is not programmed, the turning speed in each gear is limited by its machine parameter G00FEED. Programming the turning speed limit. The speed limit for all the spindles of the channel may be programmed in the same block. This function may be programmed while the spindle is running; in this case, the CNC will limit the speed to the new programmed value. The turning speed limit is set by programming function G192 and then the maximum speed for each spindle. The spindle speed is represented by the spindle name followed by the desired speed. For spindles like S1, S2, etc. the "=" sign must be included between the name and the speed; the "=" is not necessary for the spindle S. Programming format. The programming format is the following; the parameters to be set appear between curly brackets. G192 S..S9={vel} {vel} Maximum spindle speed. The speed is given in rpm. G192 S1000 G192 S1=334 G192 S150 S2=350 Properties of the function and Influence of the reset, turning the CNC off and of the M30 function. Function G192 is modal. Function G192 is canceled on power-up or after an emergency. The behavior of function G192 after executing an M02 or M30 and after a reset depends on the setting of machine parameter SPDLSTOP. SPDLSTOP Behavior of function G192 Yes Functions M02, M30 and reset cancel function G192. No Functions M02, M30 and reset do not affect the spindle. The CNC maintains function G192. 7. MULTI-SPINDLE SYSTEM. SPINDLE CONTROL. G192. Turning speed limit. CNC <strong>8065</strong> (REF: 1103) ·123·
Page 1 and 2:
CNC 8065 Execution channels (Ref: 1
Page 3 and 4:
Execution channels CHAPTER 1 INTROD
Page 5 and 6:
Execution channels ABOUT THE PRODUC
Page 7:
Execution channels Software options
Page 11:
Execution channels VERSION HISTORY
Page 14 and 15:
CNC 8065 (REF: 1103) ·14· PRECAUT
Page 17 and 18:
Execution channels WARRANTY TERMS I
Page 19:
Execution channels MATERIAL RETURNI
Page 23 and 24:
INTRODUCTION. 1 This manual is dire
Page 25 and 26:
Execution channels A permanent chan
Page 27:
CONFIGURATION I
Page 30 and 31:
2. SETTING A MULTI-CHANNEL SYSTEM.
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
3. LOGIC CNC INPUTS AND OUTPUTS. CN
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
4. CNC-PLC COMMUNICATION. CNC 8065
Page 72 and 73: 4. CNC-PLC COMMUNICATION. CNC 8065
Page 81 and 82: OPERATION AND INTERFACE. 5 The chan
Page 83 and 84: Execution channels Messages active
Page 85 and 86: Execution channels 5.3 Channel sync
Page 87 and 88: PROGRAMMING IN A SYSTEM WITH CHANNE
Page 89 and 90: Execution channels 6.2 Executing a
Page 91 and 92: Execution channels 6.3.1 Set a new
Page 93 and 94: Execution channels 6.3.2 Add a new
Page 95 and 96: Execution channels 6.3.3 Remove an
Page 97 and 98: Execution channels Accessing the va
Page 99 and 100: Execution channels 6.3.6 Variables
Page 101 and 102: Execution channels 6.4.1 Set a new
Page 103 and 104: Execution channels 6.4.3 Remove a s
Page 105 and 106: Execution channels 6.4.5 Cancel the
Page 107 and 108: Execution channels 6.5 Communicatio
Page 109 and 110: Execution channels 6.5.2 Synchroniz
Page 113 and 114: MULTI-SPINDLE SYSTEM. SPINDLE CONTR
Page 115 and 116: Execution channels If two or more s
Page 117 and 118: Execution channels 7.2 Spindle spee
Page 121: Execution channels SPINDLE SPEED IN
Page 125 and 126: Execution channels 7.5 M03/M04/M05.
Page 127 and 128: Execution channels 7.6 M41-M44. Gea
Page 129 and 130: Execution channels 7.7 M19. Spindle
Page 133 and 134: Execution channels ·sn· Name, log
Page 135 and 136: Execution channels CNC 8065 (REF: 1
show all

EN: man_8065_chn.pdf - Fagor Automation

Create successful ePaper yourself

Delete template?

Save as template?