EN: man_8065_chn.pdf - Fagor Automation

More documents

Recommendations

Info

6. PROGRAMMING IN A SYSTEM WITH CHANNELS. Axis swapping. CNC 8065 (REF: 1103) ·92· Command. Meaning. ORGOF Include zero offset. MEASOF Include measurement offset. MANOF Include the offset of the manual operations. #SET AX [X,Y,Z] ALL #SET AX [X,Y,V1,0,A] ORGOF FIXOF Execution channels
Execution channels 6.3.2 Add a new axis to the configuration of the channel. The instruction #CALL AX may be used to add one or several axes to the channel being possible to define the position to be placed in the channel. When adding new axes to the channel, the CNC behaves as follows. The CNC adds the new axes to the configuration as if they are free. If any axis is in another channel, the channel requesting the axis waits until the axis is set free. If the axis already exists in the configuration, the CNC places it in the new position. When adding an axis to the channel without defining its position, the CNC places it at the end of the channel. Optionally, one or several offsets may be applied to the defined axes. Programming. When programming this instruction, you must define the axes to be added to the channel and the position where they will be placed in the channel. Optionally, one or several offsets may be applied to the defined axes. Programming format. The programming format is the following; the parameters to be set appear between curly brackets and the optional parameters between angle brackets. #CALL AX [{xn},] {xn} Axis name. {pos} Optional. Position of the axis in the channel. {offset} Optional. One or several offsets to apply to the axes. Y ? ? Z Y ? ? Z A Y X W Z A 0.000 *****.*** *****.*** 0.000 0.000 *****.*** *****.*** 0.000 0.000 0.000 0.000 0.000 0.000 0.000 #SET AX [Y,0,0,Z] Initial channel configuration. #CALL AX [A] Add the A axis to the channel. #CALL AX [X,2,W,3] Add the X axis in position ·2· and the W axis in position ·3·. 6. PROGRAMMING IN A SYSTEM WITH CHANNELS. Axis swapping. CNC 8065 (REF: 1103) ·93·
Page 1 and 2:
CNC 8065 Execution channels (Ref: 1
Page 3 and 4:
Execution channels CHAPTER 1 INTROD
Page 5 and 6:
Execution channels ABOUT THE PRODUC
Page 7:
Execution channels Software options
Page 11:
Execution channels VERSION HISTORY
Page 14 and 15:
CNC 8065 (REF: 1103) ·14· PRECAUT
Page 17 and 18:
Execution channels WARRANTY TERMS I
Page 19:
Execution channels MATERIAL RETURNI
Page 23 and 24:
INTRODUCTION. 1 This manual is dire
Page 25 and 26:
Execution channels A permanent chan
Page 27:
CONFIGURATION I
Page 30 and 31:
2. SETTING A MULTI-CHANNEL SYSTEM.
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43: 2. SETTING A MULTI-CHANNEL SYSTEM.
Page 48 and 49: 3. LOGIC CNC INPUTS AND OUTPUTS. CN
Page 70 and 71: 4. CNC-PLC COMMUNICATION. CNC 8065
Page 81 and 82: OPERATION AND INTERFACE. 5 The chan
Page 83 and 84: Execution channels Messages active
Page 85 and 86: Execution channels 5.3 Channel sync
Page 87 and 88: PROGRAMMING IN A SYSTEM WITH CHANNE
Page 89 and 90: Execution channels 6.2 Executing a
Page 91: Execution channels 6.3.1 Set a new
Page 95 and 96: Execution channels 6.3.3 Remove an
Page 97 and 98: Execution channels Accessing the va
Page 99 and 100: Execution channels 6.3.6 Variables
Page 101 and 102: Execution channels 6.4.1 Set a new
Page 103 and 104: Execution channels 6.4.3 Remove a s
Page 105 and 106: Execution channels 6.4.5 Cancel the
Page 107 and 108: Execution channels 6.5 Communicatio
Page 109 and 110: Execution channels 6.5.2 Synchroniz
Page 113 and 114: MULTI-SPINDLE SYSTEM. SPINDLE CONTR
Page 115 and 116: Execution channels If two or more s
Page 117 and 118: Execution channels 7.2 Spindle spee
Page 121 and 122: Execution channels SPINDLE SPEED IN
Page 123 and 124: Execution channels 7.4 G192. Turnin
Page 125 and 126: Execution channels 7.5 M03/M04/M05.
Page 127 and 128: Execution channels 7.6 M41-M44. Gea
Page 129 and 130: Execution channels 7.7 M19. Spindle
Page 133 and 134: Execution channels ·sn· Name, log
Page 135 and 136: Execution channels CNC 8065 (REF: 1
show all

EN: man_8065_chn.pdf - Fagor Automation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?