EN: man_8065_chn.pdf - Fagor Automation

More documents

Recommendations

Info

4. CNC-PLC COMMUNICATION. CNC 8065 (REF: 1103) ·78· Displaying PLC errors and messages. 4.5 Displaying PLC errors and messages. Execution channels The PLC has 1024 marks for displaying messages and another 1024 marks for displaying errors at the CNC. When the mark is active, the message or the error is active. These errors and messages are common to all the channels. MSG1 - MSG1024 for displaying messages. ERR1 - ERR1024 for displaying errors. The PLC has a table for defining the messages and the errors. For more information on how to edit this table, refer to the operating manual. PLC messages. When activating one of the MSG marks, the status bar of the CNC window for PLC messages shows the message number and its associated text. If the message has a file with additional information associated with it, an access icon will appear to the left of the message. When there are more than one message activated, it always shows the one with the highest priority (the one with the lowest number). The PLC-messages window shows the "+" sign meaning that there are more messages activated by the PLC. To display the whole list, press [CTRL] + [M]. If the "Show" field of the message is selected, the CNC screen shows the additional information file and if there isn't one, a blue window with the text of the message. If the "Show" field is not selected, to show the additional information file, you must expand the list of messages, select a message and press [ENTER] or click on the message. To close the additional data window, press [ESC]. PLC errors. The message does not have a file with additional information. The message has a file with additional information. When activating one of the ERR marks, the CNC interrupts the execution of the part-program and it displays a window in the middle of the screen showing the error number and its associated text. If the error has the "Emergen" field selected, the error will open the emergency relay of the CNC. If the error has a file with additional information associated with it, an access icon will appear to the right of the error number. If the error has the "Show" field selected, the CNC shows the additional information file directly on the screen. If the "Show" field is not selected, the additional information file will be displayed when pressing the [HELP] key or when clicking on the icon mentioned earlier. To close the additional data window, press [ESC]. External inputs should be used to activate and deactivate error marks, thus preventing the CNC from receiving those errors at every new PLC cycle scan.
OPERATION AND PROGRAMMING II
Page 1 and 2:
CNC 8065 Execution channels (Ref: 1
Page 3 and 4:
Execution channels CHAPTER 1 INTROD
Page 5 and 6:
Execution channels ABOUT THE PRODUC
Page 7:
Execution channels Software options
Page 11:
Execution channels VERSION HISTORY
Page 14 and 15:
CNC 8065 (REF: 1103) ·14· PRECAUT
Page 17 and 18:
Execution channels WARRANTY TERMS I
Page 19:
Execution channels MATERIAL RETURNI
Page 23 and 24:
INTRODUCTION. 1 This manual is dire
Page 25 and 26:
Execution channels A permanent chan
Page 27: CONFIGURATION I
Page 30 and 31: 2. SETTING A MULTI-CHANNEL SYSTEM.
Page 48 and 49: 3. LOGIC CNC INPUTS AND OUTPUTS. CN
Page 70 and 71: 4. CNC-PLC COMMUNICATION. CNC 8065
Page 81 and 82: OPERATION AND INTERFACE. 5 The chan
Page 83 and 84: Execution channels Messages active
Page 85 and 86: Execution channels 5.3 Channel sync
Page 87 and 88: PROGRAMMING IN A SYSTEM WITH CHANNE
Page 89 and 90: Execution channels 6.2 Executing a
Page 91 and 92: Execution channels 6.3.1 Set a new
Page 93 and 94: Execution channels 6.3.2 Add a new
Page 95 and 96: Execution channels 6.3.3 Remove an
Page 97 and 98: Execution channels Accessing the va
Page 99 and 100: Execution channels 6.3.6 Variables
Page 101 and 102: Execution channels 6.4.1 Set a new
Page 103 and 104: Execution channels 6.4.3 Remove a s
Page 105 and 106: Execution channels 6.4.5 Cancel the
Page 107 and 108: Execution channels 6.5 Communicatio
Page 109 and 110: Execution channels 6.5.2 Synchroniz
Page 113 and 114: MULTI-SPINDLE SYSTEM. SPINDLE CONTR
Page 115 and 116: Execution channels If two or more s
Page 117 and 118: Execution channels 7.2 Spindle spee
Page 121 and 122: Execution channels SPINDLE SPEED IN
Page 123 and 124: Execution channels 7.4 G192. Turnin
Page 125 and 126: Execution channels 7.5 M03/M04/M05.
Page 127 and 128: Execution channels 7.6 M41-M44. Gea
Page 129 and 130:
Execution channels 7.7 M19. Spindle
Page 131 and 132:
Execution channels 7.7.1 Variables
Page 133 and 134:
Execution channels ·sn· Name, log
Page 135 and 136:
Execution channels CNC 8065 (REF: 1
show all

EN: man_8065_chn.pdf - Fagor Automation

Create successful ePaper yourself

Delete template?

Save as template?