EN: man_8065_chn.pdf - Fagor Automation

More documents

Recommendations

Info

2. SETTING A MULTI-CHANNEL SYSTEM. Setting the PLC program. CNC 8065 (REF: 1103) ·46· Execution channels
LOGIC CNC INPUTS AND OUTPUTS. 3 CNC's physical inputs and outputs are the set of system inputs and outputs that are governed by the PLC and communicate with the outside world through CNC connectors. The CNC also has a number of logic inputs and outputs to exchange the internal data with the marks and registers of the PLC. This way, the PLC has access to some internal CNC data. Each of these logic inputs and outputs may be referred to using its associated mnemonic. The mnemonics that begin with a "_" sign indicate that the signal is active low (0 V.); the rest of the signals are active high. CNCREADY _ALARM AUXEND _EMERGEN MANUAL _STOP Specific signals for a multi-channel system. Here is a summary of the specific signals of a multi-channel, multi-spindle and/or multimagazine system. Refer to the installation manual for further detail about each one of them. The PLC has more signals, e.g. the general signals of the CNC, of the axes, of the keys, etc. but since they have nothing to do with configuring a multi-channel system, they are not mentioned in this documentation. Refer to the installation manual for further detail about each one of them. The specific logic signals for configuring a system with channels are grouped as follows: General signals. Signals related to the –M– auxiliary functions. Signals related to the –H– auxiliary functions. Channel synchronizing signals. The specific logic signals for configuring a system with several spindles are grouped as follows: Signals related to the –S– auxiliary functions. Spindle signals. The specific logic signals for configuring a system with several tool magazines are grouped as follows: Tool manager signals. CNC 8065 (REF: 1103) ·47·
Page 1 and 2: CNC 8065 Execution channels (Ref: 1
Page 3 and 4: Execution channels CHAPTER 1 INTROD
Page 5 and 6: Execution channels ABOUT THE PRODUC
Page 7: Execution channels Software options
Page 11: Execution channels VERSION HISTORY
Page 14 and 15: CNC 8065 (REF: 1103) ·14· PRECAUT
Page 17 and 18: Execution channels WARRANTY TERMS I
Page 19: Execution channels MATERIAL RETURNI
Page 23 and 24: INTRODUCTION. 1 This manual is dire
Page 25 and 26: Execution channels A permanent chan
Page 27: CONFIGURATION I
Page 30 and 31: 2. SETTING A MULTI-CHANNEL SYSTEM.
Page 48 and 49: 3. LOGIC CNC INPUTS AND OUTPUTS. CN
Page 70 and 71: 4. CNC-PLC COMMUNICATION. CNC 8065
Page 81 and 82: OPERATION AND INTERFACE. 5 The chan
Page 83 and 84: Execution channels Messages active
Page 85 and 86: Execution channels 5.3 Channel sync
Page 87 and 88: PROGRAMMING IN A SYSTEM WITH CHANNE
Page 89 and 90: Execution channels 6.2 Executing a
Page 91 and 92: Execution channels 6.3.1 Set a new
Page 93 and 94: Execution channels 6.3.2 Add a new
Page 95 and 96: Execution channels 6.3.3 Remove an
Page 97 and 98:
Execution channels Accessing the va
Page 99 and 100:
Execution channels 6.3.6 Variables
Page 101 and 102:
Execution channels 6.4.1 Set a new
Page 103 and 104:
Execution channels 6.4.3 Remove a s
Page 105 and 106:
Execution channels 6.4.5 Cancel the
Page 107 and 108:
Execution channels 6.5 Communicatio
Page 109 and 110:
Execution channels 6.5.2 Synchroniz
Page 111 and 112:
Page 113 and 114:
MULTI-SPINDLE SYSTEM. SPINDLE CONTR
Page 115 and 116:
Execution channels If two or more s
Page 117 and 118:
Execution channels 7.2 Spindle spee
Page 119 and 120:
Page 121 and 122:
Execution channels SPINDLE SPEED IN
Page 123 and 124:
Execution channels 7.4 G192. Turnin
Page 125 and 126:
Execution channels 7.5 M03/M04/M05.
Page 127 and 128:
Execution channels 7.6 M41-M44. Gea
Page 129 and 130:
Execution channels 7.7 M19. Spindle
Page 131 and 132:
Page 133 and 134:
Execution channels ·sn· Name, log
Page 135 and 136:
Execution channels CNC 8065 (REF: 1
show all

EN: man_8065_chn.pdf - Fagor Automation

Create successful ePaper yourself

Delete template?

Save as template?