1928 Cadillac - GM Heritage Center

More documents

Recommendations

Info

44 COOLING SYSTEM 4. Flushing Cooling System In order to keep the Cooling System free from an excessive accumulation of sediment and scale, it should be flushed by the reverse-flow method every 4000 miles. To flush the system, the hose connection at the bottom of the radiator should be disconnected and the flushing hose attached to the radiator outlet. The flushing water will then be forced up through the radiator, back through the cylinder jackets and pump and out through the disconnected hose. The flushing operation should be continued until the water from the pump is reasonably clear The pressure of the water used in flushing the cooling system should not exceed 20 to 25 pounds as a higher pressure is liable to damage the radiator. 5. Spacing of Radiator Studs On 341-A <strong>Cadillac</strong> cars previous to engine unit 300600 and after engine unit 301200 (these numbers are approximate) , the radiator studs are 9 inches apart on centers. On cars between these two unit numbers and also on some later 152-inch chassis, the radiator studs are 15 inches apart. Whenever a radiator core having the studs 15 inches apart requires replacement, it will be necessary to remove the anchorage from the old core and use it with the new core to permit installing the new radiator on the chassis. To replace the anchorage, it is simply necessary to remove the two bolts which hold the anchorage on each side. 6. Operation of Thermostat The thermostat plunger should start its stroke at a temperature of not less than 150° and should have a full stroke of Jf inch at a temperature of not over 175°. The test may be made by placing the thermostat in water of the proper temperature. 7. Adjustment of Shutter Rod The yoke end of the shutter operating rod should be adjusted to bring the center of the hole in the yoke about Y% inch beyond the center of the holes in the operating arms when the rod is detached. Plate 23, Fig. 4.
COOLING SYSTEM 45 Fig. 2 Enlarged holes in water pump flange to permit lining up inlet with radiator connection Fig. 1 Sectional view of water pump These flat washers must be in place; otherwise screws will bottom on chain housing and cause oil leak Shutter control rod Fig. 3 Front view of radiator showing thermostat and shutter control Wrench 108128 Fig..4 Adjustment of shutter control rod Trunnion screw Rubber gasket Trunnion Fig. 5 To remove thermostat unscrew retaining nut Fig. 6 Thermostat assembly. To disassemble remove trunnion screw Serrated washer Fig. 9 Radiator support Adjusting nut Anti-squeak Locking collar Fig. 7 Thermostat cover assembly Fig. 8 Thermostat Plate 23. Cooling System Details.
Page 1 and 2:
f CADILLAC MOTOR CAR COMPANY & I \
Page 3 and 4:
I THE X E W (' A DILL A C 9 etaiL o
Page 5 and 6:
THE NEW CADILLAC A SURPASSING POWER
Page 7 and 8:
TIIK NEW CADILLAC KIGIDITY OF CHANK
Page 9 and 10:
T1IK NEW CADILLAC DETAILS OF OOXHT1
Page 11 and 12:
THE NEW CADILLAC DETAILS OK COXSTHC
Page 13 and 14:
THE XKW CADILLAC arranged in an ind
Page 15 and 16:
THE N li W (.UHLLAC e ull floating
Page 17 and 18:
KKI'AII.S OK COXSTK (CTION PART CAD
Page 19 and 20:
THK XKW CADILLAC ie long wheelba.se
Page 21 and 22:
DETAILS III' COXSTUI'CTION Wider, d
Page 23 and 24:
THE NEW CADILLAC out" under the rea
Page 25 and 26:
THE NEW CADILLAC in. narrow rim wit
Page 27 and 28:
Copyright 1*>2S bv adiliac Motor Ca
Page 29 and 30:
CHAPTER V—Care of Tires 63 Inflat
Page 31 and 32:
10 CADILLAC OPERATORS MANUAL OPERAT
Page 33 and 34:
14 CADILLAC OPERATOR'S MANUAL OPERA
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
30 CADILLAC OPERATOR'S MANUAL The T
Page 43 and 44:
34 CADILLAC OPERATOR'S MANUAL Infla
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
PART II LUBRICATION AND CARE
Page 51 and 52:
50 CADILLAC OPERATOR'S MANUAL LUBRI
Page 53 and 54:
54 CADILLAC OPERATOR'S MANUAL LUBRI
Page 55 and 56:
LUBRICATION AND CARE 59 Wheels; 1,
Page 57 and 58:
62 CADILLAC OPERATOR'S MANUAL Do no
Page 59 and 60:
CHAPTER VI Storing Car IF THE car i
Page 61 and 62:
GENERAL INFORMATION 71 CHAPTER I En
Page 63 and 64:
74 CADILLAC OPERATOR'S MANUAL GENER
Page 65 and 66:
GENERAL INFORMATION 79 Water Circul
Page 67 and 68:
GENERAL INFORMATION 83 u .">o I*. T
Page 69 and 70:
86 CADILLAC OPERATOR'S MANUAL it ca
Page 71 and 72:
90 CADILLAC OPERATOR'S MANUAL the c
Page 73 and 74:
94 CADILLAC OPERATOR'S MANUAL (Fig.
Page 75 and 76:
Description CHAPTER VI Steering Gea
Page 77 and 78:
102 CADILLAC OPERATOR'S MANUAL CHAP
Page 79 and 80:
106 CADILLAC OPERATOR'S MANUAL GENE
Page 81 and 82:
lid CADILLAC OPERATOR'S MANUAL GENE
Page 83 and 84:
GENERAL INFORM ATION 115 Type of en
Page 85 and 86:
118 CADILLAC OPERATOR'S MANUAL Solu
Page 87 and 88:
CADILLAC Operator's Manual CADILLAC
Page 89 and 90:
CHAPTER I Cadillac Service THE owne
Page 91 and 92:
CADILLAC OPERATOR'S MANUAL best pos
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
20 CADILLAC OPERATOR'S MANUAL Speed
Page 99 and 100:
24 CADILLAC OPERATOR'S MANUAL EQUIP
Page 101 and 102:
Page 103 and 104:
CADILLAC OPERATOR'S MANUAL EQUIPMEN
Page 105 and 106:
Page 107 and 108:
V | HfScS OWNE -R'^ ADDR F-crc ENGH
Page 109 and 110:
LUBRICATION 45 44 CADILLAC OPERATOR
Page 111 and 112:
48 CADILLAC OPERATOR'S MANUAL Winte
Page 113 and 114:
52 CADILLAC OPERATOR'S MANUAL GENER
Page 115 and 116:
STORING CAR 57 CHAPTER VII Storing
Page 117 and 118:
60 CADILLAC OPERATOR'S MANUAL porta
Page 119 and 120:
.19?fl Shop Manual Cad'llac 3^1-.^3
Page 121 and 122:
Foreword HPHIS Shop Manual is a boo
Page 123 and 124:
4 CONTENTS Engine Specifications 63
Page 125 and 126:
Front Axle Subject Cadillac 341 LaS
Page 127 and 128:
FRONT AXLE 9 Punch 1/8-inch hole in
Page 129 and 130:
FRONT AXLE 11 r~\ Front —A— f~\
Page 131 and 132:
Rear Axle and Torsion Tube Subject
Page 133 and 134:
REAR AXLE AND TORSION TUBE 15 Drive
Page 135 and 136:
REAR AXLE AND TORSION TUBE 17 To di
Page 137 and 138:
Note: Adjustment of connections,whe
Page 139 and 140:
Note: Adjustment of connections, wh
Page 141 and 142:
24 BRAKES Note: Unless brake connec
Page 143 and 144:
Note: Adjustment of connections mus
Page 145 and 146:
Note: Adjustment of connections mus
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Clutch Subject Cadillac 341 1-aSall
Page 153 and 154:
CLUTCH 37 Rear driving plate Center
Page 155 and 156:
CLUTCH 39 Rod to clutch pedal Ball
Page 157 and 158:
42 COOLING SYSTEM Filler Assemble w
Page 159 and 160:
44 COOLING SYSTEM 4. Flushing Cooli
Page 161 and 162:
Electrical System Subject Cadillac
Page 163 and 164:
ELECTRICAL SYSTEM 49 Subject Cadill
Page 165 and 166:
ELECTRICAL SYSTEM 51 Subject Cadill
Page 167 and 168:
ELECTRICAL 53 Fig.l Top view with h
Page 169 and 170:
ELECTRICAL 55 Fig. 2 Electrolock fr
Page 171 and 172:
CIRCUIT BREAKER INSTRUMENT PANEL LA
Page 173 and 174:
CUT-OUT RELAY CIRCUIT BREAKERS LOCK
Page 175 and 176:
A-T#JL-6-B-3CP8ULB B-5TOP-6-8-2ICP.
Page 177 and 178:
Intake header shield (not used on L
Page 179 and 180:
66 ENGINE To remove chain, remove c
Page 181 and 182:
68 ENGINE Fig. 1 Numbering of conne
Page 183 and 184:
70 ENGINE Use new wood plugs when r
Page 185 and 186:
72 ENGINE dicated with a dial indic
Page 187 and 188:
ENGINE 100-600 pounds press fit Pis
Page 189 and 190:
76 FRAME Plate 41. Diagrams of Cadi
Page 191 and 192:
78 GASOLINE SYSTEM Automatic thrott
Page 193 and 194:
80 GASOLINE SYSTEM Fig. 1 Cadillac
Page 195 and 196:
82 LIGHTING SYSTEM One-half of dist
Page 197 and 198:
IS p l-h n •*» 0\ r ^- o rt- **
Page 199 and 200:
Each "G" indicates a grease-gun con
Page 201 and 202:
Springs Subject Cadillac 341 LaSall
Page 203 and 204:
Subject Cadillac 341 Steering Gear
Page 205 and 206:
STEERING GEAR 93 Clamp bolt Turn nu
Page 207 and 208: High and intermediate sliding coupl
Page 209 and 210: 98 TRANSMISSION AND UNIVERSAL JOINT
Page 211 and 212: Sliding coupling with external teet
Page 213 and 214: 2 re
Page 215 and 216: Shifter forks Shifter shaft and int
Page 217 and 218: Wheels, Rims and Tires Subject Cadi
Page 219 and 220: ( i tJ^, a (.,(,1,11,1¼ BO.l •ft
Page 221 and 222: Contents DM 01 - 6 c P p^ NOTE: The
Page 223 and 224: Introduction 0Q*° ! Arrangements o
Page 225 and 226: Sf f\ £> ^ FRONT AXLE **J (¾ Subj
Page 227 and 228: 10 FRONT AXLE Adjustable lever Knuc
Page 229 and 230: 12 FRONT AXLE m^ e- -e- 1/32 inch I
Page 231 and 232: 14 REAR AXLE AND TORSION TUBE 1. Lu
Page 233 and 234: 16 REAR AXLE AND TORSION TUBE Drive
Page 235 and 236: c c Subject FOOT BRAKES Front and R
Page 237 and 238: BRAKES 21 Subject Cadillac 341 LaSe
Page 239 and 240: BRAKES 23 Note: [links Unless brake
Page 241 and 242: BRAKES 25 Lever on rocker shaft Cen
Page 243 and 244: .^ ,., i—- m m Equalizer ba 5 Adj
Page 245 and 246: .""> Use upper hole for 14-inch fro
Page 247 and 248: BRAKES 31 Note: Unless brake connec
Page 249 and 250: BRAKES 33 Note: Unless brake connec
Page 251 and 252: 36 CLUTCH Subject Cadillac 341 LaSa
Page 253 and 254: 38 CLUTCH /Test by hand, not by foo
Page 255 and 256: Cooling System Subject Cadillac 341
Page 257: COOLING SYSTEM 43 Subject Cadillac
Page 261 and 262: 48 ELECTRICAL Fig. 1 Sectional view
Page 263 and 264: 50 ELECTRICAL Spring adjusting scre
Page 265 and 266: 52 ELECTRICAL SYSTEM 5. Adding Wate
Page 267 and 268: 54 ELECTRICAL Tool I0i Fig. 1 Testi
Page 269 and 270: Adjustment of starter switch. 1 Scr
Page 271 and 272: oo A-TML-64-3 CP BULB B-STOH-M-SIC*
Page 273 and 274: s A-Wi.-«-s-sc.PNx» B-noP-64-ncit
Page 275 and 276: Engine Subject Cadillac 341 LaSalle
Page 277 and 278: ENGINE 65 Subject Cadillac 341 LaSa
Page 279 and 280: ENGINE 67 Subject Cadillac 341 USal
Page 281 and 282: ENGINE 69 Subject Cadillac 341 USal
Page 283 and 284: c Subject INLET VALVES Clearance be
Page 285 and 286: C) ENGINE 73 By-pass adjusting scre
Page 287 and 288: Frame Subject Cadillac 341 LaSalle
Page 289 and 290: Gasoline System Subject Cadillac 34
Page 291 and 292: LaSalle inlet connection and strain
Page 293 and 294: Lighting System Subject Cadillac 34
Page 295 and 296: ( Lubrication Subject Cadillac 341
Page 297 and 298: \ rs ^ Rear shackles Brake shafts u
Page 299 and 300: \ ^N Each "G" indicates a grease-gu
Page 301 and 302: 90 SPRINGS AND SHOCK ABSORBERS -Bol
Page 303 and 304: 90B SPRINGS AND SHOCK ABSORBERS Sub
Page 305 and 306: 92 STEERING GEAR First-type screw.
Page 307 and 308: 94 STEERING GEAR Steering gear arm
Page 309 and 310:
High and intermediate sliding coupl
Page 311 and 312:
98 TRANSMISSION AND UNIVERSAL JOINT
Page 313 and 314:
98-B TRANSMISSION AND UNIVERSAL JOI
Page 315 and 316:
8 H yo > z Cfl *•« Cfl Cfl e-i O
Page 317 and 318:
pq Drum engaged B with cone and syn
Page 319 and 320:
Shifter forks Shifter shaft igh and
Page 321 and 322:
Wheels, Rims and Tires Subject Cadi
show all

1928 Cadillac - GM Heritage Center

Create successful ePaper yourself

Delete template?

Save as template?