ASXpress Operator's Manual - CETAC Technologies

More documents

Recommendations

Info

ASXpress Rapid Sample Introduction System Operator’s Manual Chapter 10: Safety and Regulatory Information 10 Safety and Regulatory Information Review this product and related documentation to familiarize with safety markings and instructions before you operate the instrument. 10.1 Characteristics 10.1.1 Environmental Characteristics Operating Temperature +13° C to +30° C (+55° F to +85° F) Non-Operating Temperature +0° C to +55° C (+32° to +131° F) Operating Altitude Relative Humidity Up to 2,000 m (6,562 ft) 0% to 60% non-condensing Pollution Degree Pollution Degree 2 Table 9-2: Environmental Characteristics For indoor use only. Normally no pollution or only dry, nonconductive pollution occurs. The pollution has no influence. Occasionally, however, a temporary conductivity caused by condensation may be expected. Avoid sudden, extreme temperature changes which could cause condensation on circuit boards in the product. See page 10 for information on chemical compatibility. 10.1.2 Electrical Characteristics 10.1.2.1 Power requirements Electronics Module Input: Power is provided by the CETAC autosampler through the power/signal cable which is attached to the electronics module. DC Voltage and Current 24 V 2.5 A Installation Category: CAT I (Mains isolated) Output: Connector for the valve/pump module. Valve/Pump Module Input: Use only with the provided electronics module. Installation Category: CAT I (Mains isolated) Table 9-3: Power Requirements 126
ASXpress Rapid Sample Introduction System Operator’s Manual Chapter 10: Safety and Regulatory Information 10.1.2.2 Input and output connectors All terminals allow a maximum current of 500MA @ 24VDC, unless otherwise noted. Auto Sampler V/P Module Power and signal connection to a CETAC autosampler. Control and 0-24 V DC power for the valve/pump module. Connect only to the provided CETAC valve/pump module, using the provided cable. Table 9-4: Electrical Input and Output Connectors on the Electronics Module 127
Page 1 and 2:
CETAC ASXPRESS Rapid Sample Introdu
Page 3 and 4:
Contents
Page 5 and 6:
ASXpress Rapid Sample Introduction
Page 7 and 8:
1 Introduction
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
2 Preparing for Installation
Page 17 and 18:
Page 19 and 20:
3 Installing the Rapid Sample Intro
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76: ASXpress Rapid Sample Introduction
Page 81 and 82: 4 Verifying Installation/ Function
Page 89 and 90: 5 Using the Rapid Sample Introducti
Page 95 and 96: 6 Maintaining the Rapid Sample Intr
Page 103 and 104: 7 Troubleshooting the Rapid Sample
Page 113 and 114: 8 Glossary
Page 115 and 116: 9 Guide to Operating a CETAC Autosa
Page 125: ASXpress Rapid Sample Introduction
Page 133 and 134: Index
Page 136: Manual Part Number 480166 Rev 4 Pri
show all

ASXpress Operator's Manual - CETAC Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?