ASXpress Operator's Manual - CETAC Technologies

More documents

Recommendations

Info

ASXpress Rapid Sample Introduction System Operator’s Manual Chapter 3: Installing the Rapid Sample Introduction System 3.1.1 Install the Auxiliary I/O Connector Card and Processor (Rabbit) Module The proper processor module (with ASXPRESS functionality firmware preloaded) and auxiliary board (daughter board) with female I/O connector are furnished with the ASXPRESS system, either installed in the autosampler for full systems, or included as components of the upgrade kit version. (The I/O board connector as it appears as viewed at the rear panel of the ASX-520 autosampler is shown in Figure 1-25.) Follow the instructions in this section to install the “Rabbit” processor module and auxiliary board (daughter board) in the autosampler to be upgraded to ASXPRESS functionality. Auxiliary board installation instructions are provided in hard copy and on the CD provided in the ASXPRESS completion kit of upgrade versions.) This guide describes the necessary steps for adding an Auxiliary I/O board, and to replace the “Rabbit” module to the main board on the ASX- 260, ASX-520 and ASX-520HS autosamplers. Steps 1-8 are similar for the ASX-260, ASX-520 and ASX-520HS autosamplers. Steps 9 through completion steps of the I/O board/rabbit processor module installation instructions are split into two sections, applying to ASX-260 and ASX- 520/520HS models, respectively. See the appropriate section of this manual that applies to your CETAC autosampler. Note: The photos in this manual depict instrument components that may differ in appearance to your actual equipment, as those components may have seen update/revision. Every effort has been made to depict components as accurately as possible, as will apply to customers using CETAC instruments from a varying range of eras. 3.1.1.1 Accessing the Interior of the Autosampler 1. Place the autosampler on a flat surface (Figure 1-4/Figure 1-5) and ensure that the unit is powered off. Figure 1-4 Front view of ASX-520 Autosampler. 22
ASXpress Rapid Sample Introduction System Operator’s Manual Chapter 3: Installing the Rapid Sample Introduction System Figure 1-5 Front view of ASX-260 Autosampler. 2. Remove the two Kynar thumbscrews from the Y-axis home block (Figure 1-6). Figure 1-6 View of Y-axis home block with Kynar thumbscrews (ASX-260 and ASX-520). 23
Page 1 and 2: CETAC ASXPRESS Rapid Sample Introdu
Page 3 and 4: Contents
Page 5 and 6: ASXpress Rapid Sample Introduction
Page 7 and 8: 1 Introduction
Page 15 and 16: 2 Preparing for Installation
Page 19 and 20: 3 Installing the Rapid Sample Intro
Page 21: ASXpress Rapid Sample Introduction
Page 73 and 74:
ASXpress Rapid Sample Introduction
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
4 Verifying Installation/ Function
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
5 Using the Rapid Sample Introducti
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
6 Maintaining the Rapid Sample Intr
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
7 Troubleshooting the Rapid Sample
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
8 Glossary
Page 115 and 116:
9 Guide to Operating a CETAC Autosa
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Index
Page 136:
Manual Part Number 480166 Rev 4 Pri
show all

ASXpress Operator's Manual - CETAC Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?