ASXpress Operator's Manual - CETAC Technologies

More documents

Recommendations

Info

ASXpress Rapid Sample Introduction System Operator’s Manual Chapter 10: Safety and Regulatory Information 10.2 Safety Notices WARNING If the equipment is used in a manner not specified by CETAC Technologies, the protection provided the equipment may be impaired. Repair or service that this not covered in this manual should only be performed by qualified personnel. 10.2.1 Mains Disconnect The autosampler is the disconnect. To remove power in an emergency, disconnect the autosampler. Ensure the autosampler is positioned to allow easy disconnection. WARNING SHOCK HAZARD Ensure that power is disconnected before removing any covers. 128
ASXpress Rapid Sample Introduction System Operator’s Manual Chapter 10: Safety and Regulatory Information 10.2.2 Cleaning Instructions For additional cleaning information, see “cleaning” in the index. To clean the exterior surfaces of the instrument, complete the following steps: 1 Shut down and unplug the instrument. 2 Wipe the instrument exterior surfaces only using a towel dampened with a lab-grade cleaning agent. 3 Repeat step 2, using a towel dampened with clear water. 4 Dry the instrument exterior using a dry towel. WARNING SHOCK HAZARD Do not allow any liquid to enter the instrument cabinet other than as intended through the specified tubing, or come into contact with any electrical components. The instrument must be thoroughly dry before you reconnect power, or turn the instrument on. 10.2.3 Operating Environment WARNING SHOCK HAZARD To reduce the risk of fire hazard and electrical shock, do not expose the unit to rain or humidity. To reduce the risk of electrical shock, do not open the cabinet. All maintenance is to be performed by an Authorized CETAC Service Provider. Protection provided by the equipment may be impaired if the equipment is used in a manner not specified by the manufacturer. WARNING SHOCK HAZARD Equipment is not intended for wet locations. Miscellaneous liquids in the equipment could cause hazardous conditions. WARNING EXPLOSION HAZARD Do not operate in an explosive atmosphere. 10.2.4 Explanation of Caution and Warning Notices 129
Page 1 and 2:
CETAC ASXPRESS Rapid Sample Introdu
Page 3 and 4:
Contents
Page 5 and 6:
ASXpress Rapid Sample Introduction
Page 7 and 8:
1 Introduction
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
2 Preparing for Installation
Page 17 and 18:
Page 19 and 20:
3 Installing the Rapid Sample Intro
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78: ASXpress Rapid Sample Introduction
Page 81 and 82: 4 Verifying Installation/ Function
Page 89 and 90: 5 Using the Rapid Sample Introducti
Page 95 and 96: 6 Maintaining the Rapid Sample Intr
Page 103 and 104: 7 Troubleshooting the Rapid Sample
Page 113 and 114: 8 Glossary
Page 115 and 116: 9 Guide to Operating a CETAC Autosa
Page 127: ASXpress Rapid Sample Introduction
Page 133 and 134: Index
Page 136: Manual Part Number 480166 Rev 4 Pri
show all

ASXpress Operator's Manual - CETAC Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?