ASXpress Operator's Manual - CETAC Technologies

More documents

Recommendations

Info

ASXpress Rapid Sample Introduction System Operator’s Manual Chapter 3: Installing the Rapid Sample Introduction System 3.4 Upgrade the Firmware on the Autosampler The CETAC autosampler requires a firmware version which is compatible with the ASXPRESS system. The ASXPRESS full system versions are shipped with the firmware pre-loaded onto the Rabbit module which is pre-installed inside the autosampler. ASXPRESS upgrade versions (those which include the ASXPRESS system only, and are intended for upgrade of a customer’s existing ASX-520 series autosamplers) include a Rabbit processor module with firmware preloaded. This Rabbit processor module shall be installed in the autosampler to be upgraded, replacing the existing module. Replacement of this module is discussed in detail in prior sections within this chapter of this manual. Note: This manual section is included to provide instruction the event that a customer requires to reload the ASXPRESS firmware, or to upgrade firmware to subsequent versions as CETAC advances its technology. It is not necessary to load firmware on full system or upgrade version ASXPRESS instruments as shipped from the factory. A compatible firmware version and Rabbit Firmware Utility (RFU) Upgrade program is included on the CD provided with the ASXPRESS completion kit. Complete instructions for loading the firmware is also provided on the CD. Follow the provided instructions to upgrade the firmware on the autosampler. See the CETAC Autosampler Operator Manual for any further instructions on autosampler set up. The following guide describes the necessary steps for upgrading the firmware on the ASX-260/520 and ASX-520HS autosamplers. 3.4.1 Autosampler Programming Configuration The autosampler’s Rabbit processor module must be configured to receive the firmware. This is achieved by moving jumpers on the main board to place the system into “programming mode”. Follow the instructions in the following section to complete the firmware upgrade. 1. Ensure that the autosampler is powered off, and that all covers are removed as is outlined in Section 3.1.1. 2. On the ASX-520/520HS board, move jumper JP3 and JP4 to JP5 and JP6 (Figure 3-60 shows jumpers). 70
ASXpress Rapid Sample Introduction System Operator’s Manual Chapter 3: Installing the Rapid Sample Introduction System Note: Main boards of different versions may have varying locations/positions/quantities of available jumper positions. Follow nomenclature present on the board for proper jumper positioning. Figure 1-60 Jumpers on board in normal mode (ASX-520). 71
Page 1 and 2:
CETAC ASXPRESS Rapid Sample Introdu
Page 3 and 4:
Contents
Page 5 and 6:
ASXpress Rapid Sample Introduction
Page 7 and 8:
1 Introduction
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
2 Preparing for Installation
Page 17 and 18:
Page 19 and 20: 3 Installing the Rapid Sample Intro
Page 21 and 22: ASXpress Rapid Sample Introduction
Page 69: ASXpress Rapid Sample Introduction
Page 81 and 82: 4 Verifying Installation/ Function
Page 89 and 90: 5 Using the Rapid Sample Introducti
Page 95 and 96: 6 Maintaining the Rapid Sample Intr
Page 103 and 104: 7 Troubleshooting the Rapid Sample
Page 113 and 114: 8 Glossary
Page 115 and 116: 9 Guide to Operating a CETAC Autosa
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Index
Page 136:
Manual Part Number 480166 Rev 4 Pri
show all

ASXpress Operator's Manual - CETAC Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?