DSLBD Office Fit Out - Broughton Construction Company

More documents

Recommendations

Info

C. Static-Dissipative Rubber Floor Tile: ASTM F 1344, except in manufacturer's standard hardness when tested per ASTM D 2240 using Shore, Type A durometer. 1. Raised-Disc Tile: Class I-A (homogenous rubber, solid color); tiles 39.37 by 39.37 inches (1000 by 1000 mm); 0.20-inch (5.0-mm) overall thickness, 0.19-inch (4.7-mm) base thickness. 2. Hammered-Surface Textured Tile: Class I-B (homogenous rubber, through-mottled pattern). 3. Smooth or Textured Surface Tile: Class I-B (homogenous rubber, through-mottled pattern). D. Static-Dissipative Vinyl Sheet Floor Covering: ASTM F 1913 (unbacked) or ASTM F 1303, Type II, Grade I, Class B (nonfoamed plastic backing); in manufacturer's standard roll size; in manufacturer's standard thickness, but not less than 0.08 inch (2.0 mm) thick. E. Static-Dissipative Rubber Sheet Floor Covering: ASTM F 1859, Type I (homogenous); in manufacturer's standard roll width and length; not less than 0.08 inch (2.0 mm). F. Static-Dissipative Recycled Rubber Sheet Floor Covering: Manufactured from post-consumer tire rubber; in manufacturer's standard roll width and length; 0.20 inch (5.0 mm) thick. G. Static-Control Properties: 1. Electrical Resistance: Test per ASTM F 150 with 100-V applied voltage. a. Average greater than 1 megohm and less than or equal to 1000 megohms when test specimens are tested surface to ground. b. Average no less than 1 megohm and less than or equal to 1000 megohms when installed floor coverings are tested surface to ground. 2. Static Generation: Less than 300 V when tested per AATCC-134 at 20 percent relative humidity with conductive footwear. 3. Static Decay: 5000 to 0 V in less than 0.25 seconds when tested per FED-STD-101/4046.1. H. Color: As indicated in Appendix A. 2.9 RESILIENT WALL BASE A. Wall Base: ASTM F 1861. B. Type (Material Requirement): As indicated in Appendix A. C. Group (Manufacturing Method): As indicated by product designation. D. Style, minimum thickness and height: As indicated in Appendix A. E. Lengths: Coils in manufacturer's standard length. F. <strong>Out</strong>side Corners: Job formed or premolded. G. Inside Corners: Job formed or premolded. H. Surface: Smooth. 2.10 RESILIENT MOLDING ACCESSORY RESILIENT FLOORING 09 65 00 - 6
A. Description: As indicated in Appendix A. B. Material, profile, color and dimensions: As indicated in Appendix A. 2.11 INSTALLATION MATERIALS A. Trowelable Leveling and Patching Compounds: Latex-modified, portland cement based or blended hydraulic cement based formulation provided or approved by resilient product manufacturer for applications indicated. B. Adhesives: Water-resistant type recommended by manufacturer to suit resilient products and substrate conditions indicated. 1. Use adhesive that comply with the following limits for VOC content when calculated according to 40 CFR 50, Subpart D: a. VCT Tile Adhesive: Not more than 50 g/L. b. Rubber Floor Adhesives: Not more than 60 g/L. C. Static-Control Adhesive: Adhesive product of floor covering manufacturer that produces conductive continuity of floor covering system. D. Heat-Welding Bead: Solid-strand product of floor covering manufacturer. 1. Color: Match floor covering. E. Integral-Flash-Cove-Base Accessories: 1. Cove Strip: 1-inch (25-mm) radius provided or approved by floor covering manufacturer. 2. Cap Strip: Square metal, vinyl, or rubber cap provided or approved by floor covering manufacturer. F. Static-Control Grounding Strips: Provided and approved by floor covering manufacturer and that produce conductive continuity of floor covering system to ground connection. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine substrates, with Installer present, for compliance with requirements for installation tolerances, moisture content, and other conditions affecting performance. 1. Verify that finishes of substrates comply with tolerances and other requirements specified in other Sections and that substrates are free of cracks, ridges, depressions, scale, and foreign deposits that might interfere with adhesion of resilient products. 2. Proceed with installation only after unsatisfactory conditions have been corrected. 3.2 PREPARATION A. Prepare substrates according to manufacturer's written recommendations to ensure adhesion of resilient products. B. Concrete Substrates: Prepare according to ASTM F 710. 1. Verify that substrates are dry and free of curing compounds, sealers, and hardeners. 2. Alkalinity and Adhesion Testing: Perform tests recommended by manufacturer. Proceed with installation only after substrates pass testing. RESILIENT FLOORING 09 65 00 - 7
Page 1:
PROJECT MANUAL DSLBD Offices D G S
Page 4 and 5:
TABLE OF CONTENTS Section 09 68 13
Page 6 and 7:
A. General: Contractor shall have f
Page 8 and 9:
4. Applications containing requests
Page 10 and 11:
i) Product, model and finish ii) Ac
Page 12 and 13:
2. Include a list of quantities of
Page 14 and 15:
3. Installation and removal of temp
Page 16 and 17:
PART 2 - PRODUCTS (Not Used) PART 3
Page 18 and 19:
G. Fragnet: A partial or fragmentar
Page 20 and 21:
D. Constraints: Include constraints
Page 22 and 23:
5. Changes in the critical path. 6.
Page 25 and 26:
SECTION 01 33 00 - SUBMITTAL PROCED
Page 27 and 28:
3. Resubmit submittals until they a
Page 29 and 30:
A. General: Prepare and submit Info
Page 31 and 32:
SECTION 01 35 16 - ALTERATION PROJE
Page 33 and 34:
3.03 REPAIR/RESTORATION 2. Remove u
Page 35 and 36:
SECTION 01 40 00 - QUALITY REQUIREM
Page 37 and 38:
3. Name, address, and telephone num
Page 39 and 40:
3. Where quality-control services a
Page 41 and 42:
SECTION 01 42 00 - REFERENCES PART
Page 43 and 44:
addresses are subject to change and
Page 45 and 46:
(American Society for Testing and M
Page 47 and 48:
FCI Fluid Controls Institute (216)
Page 49 and 50:
www.maplefloor.org MFMA Metal Frami
Page 51 and 52:
www.opl.com (210) 635-8100 PCI Prec
Page 53 and 54:
www.ul.com (847) 272-8800 UNI Uni-B
Page 55:
(See TRB) NIST National Institute o
Page 58 and 59:
2.2 EQUIPMENT 1. Heating Equipment:
Page 60 and 61:
C. Temporary Facility Changeover: D
Page 62 and 63:
4. Completed List: Within 60 days a
Page 64 and 65:
A. General Product Requirements: Pr
Page 66 and 67:
c. List of unacceptable installatio
Page 68 and 69:
A. General: Clean Project site and
Page 71 and 72:
SECTION 01 74 19 - CONSTRUCTION WAS
Page 73 and 74:
D. Site Access and Temporary Contro
Page 75 and 76:
SECTION 01 77 00 - CLOSEOUT PROCEDU
Page 77 and 78:
1. Bind warranties and bonds in hea
Page 79 and 80:
SECTION 01 78 23 - OPERATION AND MA
Page 81 and 82:
a. If two or more binders are neces
Page 83 and 84:
C. Product Information: Include the
Page 85:
2. Comply with requirements of newl
Page 88 and 89:
5. Locations of proposed dust- and
Page 90 and 91:
B. Temporary Facilities: Provide te
Page 93 and 94:
SECTION 06 10 00 - ROUGH CARPENTRY
Page 95 and 96:
SECTION 06 40 00 - ARCHITECTURAL WO
Page 97 and 98:
1.8 COORDINATION A. Coordinate size
Page 99 and 100:
D. Complete fabrication, including
Page 101:
C. Clean woodwork on exposed and se
Page 104 and 105:
1.4 SUBMITTALS A. Product Data: For
Page 106 and 107:
c. Fire-rated form board. d. Filler
Page 108 and 109:
1. Fill voids and cavities formed b
Page 110 and 111:
F. Warranties: Special warranties s
Page 112 and 113:
2. Type and Grade: M (multicomponen
Page 114 and 115:
e. Wood 3. Remove laitance and form
Page 117 and 118:
SECTION 08 12 16 - ALUMINUM FRAMES
Page 119:
A. Examine walls, floors, and ceili
Page 122 and 123:
1.04 SUBMITTALS 2. BLENDING - Color
Page 124 and 125:
a. Americans with Disabilities Act
Page 126 and 127:
2. Doors may, at Contractor’s opt
Page 128 and 129: B. Shop Applied Finishes: Catalyzed
Page 131 and 132: SECTION 08 42 26 - ALL-GLASS ENTRAN
Page 133 and 134: 5. Pilkington 6. Tempglass 7. Virgi
Page 135: 3.04 CLEANING 2. Use a method of at
Page 138 and 139: 2. McKinney 3. Stanley Works B. Piv
Page 140 and 141: 3.02 INSTALLATION 1. Examine doors,
Page 142 and 143: a. 5 year warranty period b. Warran
Page 144 and 145: B. Protect exterior glass from brea
Page 146 and 147: C. Sound Transmission Characteristi
Page 148 and 149: . Depth: As indicated. 3. Hat-Shape
Page 150 and 151: B. Facing: FSK (foil/scrim/kraft).
Page 152 and 153: C. Isolate steel framing from build
Page 154 and 155: D. Integrate stair hanger rods with
Page 156 and 157: 2. Wet gypsum panels on surfaces th
Page 158 and 159: 1.5 QUALITY ASSURANCE A. Qualificat
Page 160 and 161: 4. Elastomeric Sealants: a. Dow Cor
Page 162 and 163: 1. Products: a. Boiardi Products Co
Page 164 and 165: B. Metal Edge Strips: Angle or L-sh
Page 166 and 167: D. Accurately form intersections an
Page 168 and 169: 1. Remove epoxy and latex-portland
Page 171 and 172: SECTION 09 51 00 - ACOUSTICAL CEILI
Page 173 and 174: SECTION 09 65 00 - RESILIENT FLOORI
Page 175 and 176: B. Manufacturers: 1. Solid Vinyl Fl
Page 177: B. Class: As indicated by product d
Page 181 and 182: B. Match tiles for color and patter
Page 183 and 184: SECTION 09 68 13 - CARPET TILING PA
Page 185 and 186: 3. Provide a written warranty cover
Page 187: D. Clean metal substrates of grease
Page 190 and 191: PART 2 - PRODUCTS 2.01 SELECTIONS A
Page 192 and 193: 1. Number of coats specified are mi
Page 195 and 196: SECTION 11 31 00 - RESIDENTIAL APPL
Page 197 and 198: DGS OJS DSLBD ONE JUDICIARY SQUARE,
Page 199 and 200: A. Resilient Base Selections: 1. Dr
Page 201 and 202: DGSOJS DSLBD ONE JUDICIARY SQUARE,
Page 203 and 204: OJS Building Rules, Regulations, an
show all

DSLBD Office Fit Out - Broughton Construction Company

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?