Cisco Unified IP Phone 7962G and 7942G Phone Guide and Quick ...

More documents

Recommendations

Info

Using a Wireless HeadsetRefer to the wireless headset documentation for information about using the wireless headset’s remotefeatures. Also, check with your system administrator to be sure your phone is enabled to use a wirelessheadset with the wireless headset remote hookswitch control feature.Using Wideband with your HeadsetIf you use a headset that supports wideband, you might experience improved audio sensitivity if youenable the wideband setting on your phone (this setting is disabled by default). To access the setting,choose > User Preferences > Audio Preferences > Wideband Headset.If the Wideband Headset setting shows as dimmed, then this setting is not user controllable.Check with your system administrator to be sure your phone system is configured to use wideband. Ifthe system is not configured for wideband, you may not detect any additional audio sensitivity evenwhen using a wideband headset. To learn more about your headset, refer to the headset documentationor ask your system administrator for assistance.Using a SpeakerphoneMany of the actions you can take to dial a number or answer a call will automatically triggerspeakerphone mode, assuming that the handset is in its cradle and is not lit.If you want to...Toggle speakerphone mode onor offSwitch to a handsetAdjust the volume level for acallThen...Press .Lift the handset.Press during a call or after invoking a dial tone.Press Save to preserve the volume level for future calls.50 OL-19613-01
Using a Handset, Headset, and SpeakerphoneUsing AutoAnswer with a Headset or SpeakerphoneWhen AutoAnswer is enabled, your phone answers incoming calls automatically after a few rings.Your system administrator configures AutoAnswer to use either the speakerphone or a headset. Youmight use AutoAnswer if you receive a high volume of incoming calls.If you...Use AutoAnswer with aheadsetUse AutoAnswer with thespeakerphoneThen...Keep headset mode active (in other words, keepwhen you are not on a call.To keep headset mode active, do the following:• Press EndCall to hang up.• Press New Call or Dial to place new calls.illuminated), evenIf your phone is set up to use AutoAnswer in headset mode, calls areautomatically answered only if is illuminated.Otherwise, calls ring normally and you must manually answer them.Keep the handset in the cradle and headset mode inactive ( unlit).Otherwise, calls ring normally and you must manually answer them.Cisco Unified IP Phone 7962G and 7942G Phone Guide for Cisco Unified Communications Manager 7.1(2) (SCCP and SIP)
Page 1:
Cisco Unified IP Phone 7962G and794
Page 4 and 5:
GPickUpiDivertJoinLinksMainMeetMemo
Page 6 and 7:
Switching Between Multiple Calls 23
Page 8 and 9: Understanding Additional Configurat
Page 10 and 11: Finding Additional InformationYou c
Page 12 and 13: +Connecting Your PhoneYour system a
Page 14 and 15: Cisco recommends the use of good qu
Page 16 and 17: Cisco Unified IP Phone 7942G1621 34
Page 18 and 19: Item Description For more informati
Page 20 and 21: Understanding Phone Screen Features
Page 22 and 23: Understanding Feature AvailabilityD
Page 24 and 25: Basic Call HandlingYou can perform
Page 26 and 27: If you want to...Make a priority (p
Page 28 and 29: Answering a CallYou can answer a ca
Page 30 and 31: Using Hold and ResumeYou can hold a
Page 32 and 33: Switching an In-Progress Call to An
Page 34 and 35: Sending a Call to a Voice Message S
Page 36 and 37: When DND and Call Forward All are b
Page 38 and 39: Using JoinJoin allows you to combin
Page 40 and 41: Viewing or Removing Conference Part
Page 42 and 43: Advanced Call HandlingAdvanced call
Page 44 and 45: If you want to...Answer a call that
Page 46 and 47: • Your system administrator can a
Page 48 and 49: Using Barge FeaturesThe table below
Page 50 and 51: Using BLF to Determine a Line State
Page 52 and 53: NoteThere are interactions, restric
Page 54 and 55: Using Cisco Extension MobilityCisco
Page 56 and 57: - The number is not accurately matc
Page 60 and 61: Changing Phone SettingsYou can cust
Page 62 and 63: Using Call Logs and DirectoriesThis
Page 64 and 65: Tips• (SCCP and SIP phones) Your
Page 66 and 67: If you want to...Dial from a PABent
Page 68 and 69: Accessing Voice MessagesTo access v
Page 70 and 71: Configuring Features and Services o
Page 72 and 73: If you want to...Search for a Fast
Page 74 and 75: Setting Up Phone Services on the We
Page 76 and 77: TipYour PIN and password allow you
Page 78 and 79: Setting Up Phones and Access Lists
Page 80 and 81: Using Cisco WebDialerCisco WebDiale
Page 82 and 83: Understanding Additional Configurat
Page 84 and 85: Troubleshooting Your PhoneThis sect
Page 86 and 87: Cisco One-Year Limited Hardware War
Page 88 and 89: multiple, switching between 23mutin
Page 90 and 91: Ldescription of 10language (locale)
Page 92: answering calls with 20button, iden
show all

Cisco Unified IP Phone 7962G and 7942G Phone Guide and Quick ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?