1 Surgery CAMLOG Compendium

More documents

Recommendations

Info

<strong>Surgery</strong> Manual SCREW-CYLINDER-LINE Insertion Pre-drilling Ø 3.3 mm Pre-drilling Ø 3.6 mm 100 Drilling depth check after pre-drilling Ø 3.3 mm Drilling depth check after pre-drilling Ø 3.6 mm Parallelism/axis check after pre-drilling Ø 3.3 mm Parallelism/axis check after pre-drilling Ø 3.6 mm Note If a simultaneous implantation into the augmented sinus is to be performed, pre-drilling continues only until penetration of the sinus cortical bone is felt. The use of a 9-mm depth stop is for demonstration purposes only since this configuration is also universally applicable. During final form drilling, the shortest possible form drill must be used to shape the Bioseal Bevel as far as the depth stop.
Form Drilling Diameter and Lengths Diameter- and length-calibrated form drills are available for the SCREW- CYLINDER-LINE Implants. The internally irrigated form drills are color-coded and laser-marked. The form drills included in the surgery sets are supplied with a color-coded removable depth stop (height 2 mm). The implant bed is shaped to its final size with the form drill matching the selected implant size. For bone qualities D1 or D2, the use of increasing diameter form drills is recommended. Recommended drilling speeds: Ø 3.8 mm 500 rpm Ø 4.3 mm 400 rpm Ø 5.0 mm 350 rpm Ø 6.0 mm 300 rpm The protocol-compliant insertion depth for SCREW-CYLINDER-LINE Implants with depth stop in place is the implant length (9 / 11 / 13 / 16 mm) minus 0.4 mm with the circular stop at the crestal bone level, so that the implant shoulder extends 0.4 mm above the bone level. If a greater insertion depth is desirable, the depth stop can be removed and the preparation will then be guided by the depth mark. SCREW-CYLINDER-LINE form drills Ø 3.8 mm 9 mm Ø 4.3 mm Ø 5.0 mm Ø 6.0 mm Length 11 mm 13 mm 16 mm <strong>Surgery</strong> Manual SCREW-CYLINDER-LINE Insertion 101
Page 1:
CAMLOG Compendium 1 Surgery
Page 4 and 5:
CAMLOG Compendium | 1 Surgery Bibli
Page 6 and 7:
CAMLOG Compendium | 1 Surgery 4. Pr
Page 9 and 10:
I. General System Information 1. In
Page 11 and 12:
3. Implant Configuration Macroscopi
Page 13 and 14:
Bioseal Bevel/Implant Shoulder Foll
Page 15 and 16:
Tube-in-Tube Connection The long-te
Page 17 and 18:
4. Mechanics and Biomechanics Mecha
Page 19 and 20:
II. CAMLOG Concept 1. Team Concept
Page 21 and 22:
2. Treatment Concept Introduction I
Page 23 and 24:
Fixed Restorations Single Crowns Si
Page 25 and 26:
Implant-Supported Bridges Implant-s
Page 27 and 28:
Bar supported Dentures Bars are sui
Page 29 and 30:
2. Anamnesis Introduction The medic
Page 31 and 32:
Articulator Set-Up The diagnostic c
Page 33 and 34:
Planning Template A planning templa
Page 35 and 36:
5. Implant Position Verification Go
Page 37 and 38:
Final Prosthesis Design The surgica
Page 39:
SCREW-CYLINDER-LINE Implant The SCR
Page 42 and 43:
Surgery Manual CAMLOG ® Surgery Sy
Page 44 and 45:
Surgery Manual CAMLOG ® Surgery Sy
Page 46 and 47:
Surgery Manual Implant Healing 4. H
Page 48 and 49:
Surgery Manual SCREW-LINE Insertion
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59: Surgery Manual SCREW-LINE Insertion
Page 73 and 74: 6. ROOT-LINE Implant Introduction T
Page 75 and 76: Incision Line The sample indication
Page 77 and 78: 13 mm 11 mm 9 mm 13 mm 11 mm 9 mm 1
Page 79 and 80: Paralleling Pin with Depth Marks On
Page 81 and 82: Pre-Drilling An internally irrigate
Page 83 and 84: Depth Stop During form drilling the
Page 85 and 86: Form Drilling Once pre-drilling is
Page 87 and 88: Manual thread tapping is performed
Page 89 and 90: Implant Positioning The protocol-co
Page 91 and 92: Placing the PickUp on the insertion
Page 93 and 94: Next, extract the retention screw o
Page 95 and 96: Accessories Adapter for Screw Impla
Page 97: Accessories Once the retention scre
Page 100 and 101: Surgery Manual SCREW-CYLINDER-LINE
Page 124 and 125: 116
Page 126 and 127: Surgery Manual CYLINDER-LINE Insert
Page 144 and 145: 136
Page 146 and 147: Surgery Manual Healing Cap Healing
Page 148 and 149: Transfer System Introduction 10. Tr
Page 150 and 151: Transfer System Closed Impression M
Page 152 and 153: Transfer System Open Impression Met
Page 154 and 155: Transfer System Open Impression Met
Page 156 and 157: Provisional Solution Introduction 1
Page 158 and 159:
Provisional Solution Preparing the
Page 160 and 161:
General Information Torque Wrench S
Page 162 and 163:
General Information Torque Wrench C
Page 164 and 165:
156
Page 166 and 167:
Informations Materials Titanium Gra
Page 168 and 169:
160
Page 170 and 171:
162
Page 172:
➤ ➤ ISBN 978-3-13-134351-2 CAML
show all

1 Surgery CAMLOG Compendium

Create successful ePaper yourself

Delete template?

Save as template?