1 Surgery CAMLOG Compendium

More documents

Recommendations

Info

<strong>Surgery</strong> Manual SCREW-LINE Insertion Punch-Marking the Cortical Bone The Ø 2.3 mm internally irrigated round bur is used for Punch-marking the cortical bone, which secures the use of the drills to follow. The bur is inserted as far as the bur equator. Recommended drilling speed: 800 rpm. Round bur, Ø 2.3 mm 46 max. 800 rpm Punch-marking the cortical bone Pilot drilling Pilot Drilling The depth and axis orientation are prepared with the internally cooled pilot drill with reduced coil. The depth marks on the drill correspond to the implant lengths: 9 / 11 / 13 mm. The maximum drilling depth is 16 mm. For safety reasons, a depth stop matching the proposed implant length should be used. Recommended drilling speed: 800 rpm. max. 800 rpm Pilot drill with reduced coil, Ø 2.0 mm If a drilling template is used, the depth stops may be placed on the pilot drill after the positions have been marked. Once drilling is complete, the depth and axis of the implant bed are checked with the paralleling pin. If several implants are to be placed, a paralleling pin is inserted in the first hole to align the subsequent implant axes. The pilot drill is aligned parallel to the paralleling pin and visually checked on two planes (sagittal and transversal). SCREW-LINE paralleling pin Depth measurement after pilot drilling
Pre-Drilling A tapered SCREW-LINE pre-drill with a 2.8 mm coronal and 1.7 mm apical diameter is available for the SCREW- LINE configuration. The recommended drilling speed is 600 rpm. The depth marks on the drill match the implant lengths (9, 11, and 13 mm). The maximum drilling depth is 16 mm. For safety reasons, a depth stop matching the proposed implant length should be used. Further drilling is performed with the form drills. SCREW-LINE pre-drill Ø 1.7–2.8 mm Pre-drilling max. 600 rpm SCREW-LINE paralleling pin Checking the axis orientation after pre-drilling Ø 1.7 – 2.8 mm <strong>Surgery</strong> Manual SCREW-LINE Insertion Depth measurement after pre-drilling 47
Page 1:
CAMLOG Compendium 1 Surgery
Page 4 and 5: CAMLOG Compendium | 1 Surgery Bibli
Page 6 and 7: CAMLOG Compendium | 1 Surgery 4. Pr
Page 9 and 10: I. General System Information 1. In
Page 11 and 12: 3. Implant Configuration Macroscopi
Page 13 and 14: Bioseal Bevel/Implant Shoulder Foll
Page 15 and 16: Tube-in-Tube Connection The long-te
Page 17 and 18: 4. Mechanics and Biomechanics Mecha
Page 19 and 20: II. CAMLOG Concept 1. Team Concept
Page 21 and 22: 2. Treatment Concept Introduction I
Page 23 and 24: Fixed Restorations Single Crowns Si
Page 25 and 26: Implant-Supported Bridges Implant-s
Page 27 and 28: Bar supported Dentures Bars are sui
Page 29 and 30: 2. Anamnesis Introduction The medic
Page 31 and 32: Articulator Set-Up The diagnostic c
Page 33 and 34: Planning Template A planning templa
Page 35 and 36: 5. Implant Position Verification Go
Page 37 and 38: Final Prosthesis Design The surgica
Page 39: SCREW-CYLINDER-LINE Implant The SCR
Page 42 and 43: Surgery Manual CAMLOG ® Surgery Sy
Page 44 and 45: Surgery Manual CAMLOG ® Surgery Sy
Page 46 and 47: Surgery Manual Implant Healing 4. H
Page 48 and 49: Surgery Manual SCREW-LINE Insertion
Page 73 and 74: 6. ROOT-LINE Implant Introduction T
Page 75 and 76: Incision Line The sample indication
Page 77 and 78: 13 mm 11 mm 9 mm 13 mm 11 mm 9 mm 1
Page 79 and 80: Paralleling Pin with Depth Marks On
Page 81 and 82: Pre-Drilling An internally irrigate
Page 83 and 84: Depth Stop During form drilling the
Page 85 and 86: Form Drilling Once pre-drilling is
Page 87 and 88: Manual thread tapping is performed
Page 89 and 90: Implant Positioning The protocol-co
Page 91 and 92: Placing the PickUp on the insertion
Page 93 and 94: Next, extract the retention screw o
Page 95 and 96: Accessories Adapter for Screw Impla
Page 97: Accessories Once the retention scre
Page 100 and 101: Surgery Manual SCREW-CYLINDER-LINE
Page 102 and 103: Surgery Manual SCREW-CYLINDER-LINE
Page 104 and 105:
Surgery Manual SCREW-CYLINDER-LINE
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
116
Page 126 and 127:
Surgery Manual CYLINDER-LINE Insert
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
136
Page 146 and 147:
Surgery Manual Healing Cap Healing
Page 148 and 149:
Transfer System Introduction 10. Tr
Page 150 and 151:
Transfer System Closed Impression M
Page 152 and 153:
Transfer System Open Impression Met
Page 154 and 155:
Transfer System Open Impression Met
Page 156 and 157:
Provisional Solution Introduction 1
Page 158 and 159:
Provisional Solution Preparing the
Page 160 and 161:
General Information Torque Wrench S
Page 162 and 163:
General Information Torque Wrench C
Page 164 and 165:
156
Page 166 and 167:
Informations Materials Titanium Gra
Page 168 and 169:
160
Page 170 and 171:
162
Page 172:
➤ ➤ ISBN 978-3-13-134351-2 CAML
show all

1 Surgery CAMLOG Compendium

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?