1 Surgery CAMLOG Compendium

More documents

Recommendations

Info

<strong>Surgery</strong> Manual ROOT-LINE Insertion Implant Bed Preparation Overview of the implant bed preparation. • Punch mark the desired implant position with the internally irrigated Ø 3.5 mm round bur. • Deep drill along the implant axial line with the internally irrigated Ø 2.0 mm pilot drill. • Check with the Ø 2.0 / 3.3 mm paralleling pin with depth marks. • Pre-drill with the internally irrigated Ø 2.8 mm pre-drill. • Check with Ø 2.8 / 3.6 mm paralleling pin with depth marks. • Shape with internally irrigated form drill. • Probe the implant bed hole for its bony end. • Use ROOT-LINE/SCREW-CYLINDER- LINE tap (for bone qualities D1 and D2). 68 Drilling Sequence Ø 3.8 mm Ø 4.3 mm Ø 5.0 mm Ø 6.0 mm Round bur Ø 3.5 mm 16 mm 13 mm 11 mm 9 mm Depth stop Paralleling pin Ø 2.0/3.3 mm rpm 800 800 600 Round bur Ø 3.5 mm Round bur Ø 3.5 mm Round bur Ø 3.5 mm 16 mm 13 mm 11 mm 9 mm Depth stop rpm 800 800 600 16 mm 13 mm 11 mm 9 mm Depth stop rpm 800 800 600 16 mm 13 mm 11 mm 9 mm Pilot drill Ø 2.0 mm Pilot drill Ø 2.0 mm Pilot drill Ø 2.0 mm Pilot drill Ø 2.0 mm Depth stop Paralleling pin Ø 2.0/3.3 mm Paralleling pin Ø 2.0/3.3 mm Paralleling pin Ø 2.0/3.3 mm rpm 800 800 600 The height of the depth stop for the form drill is 2 mm. * If the bone quality is D1 or D2, use of the tap (thread cutter) is recommended for ROOT-LINE Implants. Pre-drill Ø 2.8 mm Pre-drill Ø 2.8 mm Pre-drill Ø 2.8 mm Pre-drill Ø 2.8 mm
13 mm 11 mm 9 mm 13 mm 11 mm 9 mm 13 mm 11 mm 9 mm 13 mm 11 mm 9 mm Depth stop * Depth stop Depth stop Depth stop Paralleling pin Ø 2.8/3.6 mm Paralleling pin Ø 2.8/3.6 mm Paralleling pin Ø 2.8/3.6 mm Paralleling pin Ø 2.8/3.6 mm Ø 3.8 Ø 3.8 Ø 3.8 Ø 3.8 Form drill Tap 500 15 Form drill Ø 4.3 500 400 15 Form drill Ø 4.3 Ø 4.3 * Tap Ø 5.0 500 400 350 15 Form drill Ø 5.0 0.4 mm Ø 6.0 0.4 mm 500 400 350 300 15 * Tap * Tap 0.4 mm <strong>Surgery</strong> Manual ROOT-LINE Insertion 0.4 mm 69
Page 1:
CAMLOG Compendium 1 Surgery
Page 4 and 5:
CAMLOG Compendium | 1 Surgery Bibli
Page 6 and 7:
CAMLOG Compendium | 1 Surgery 4. Pr
Page 9 and 10:
I. General System Information 1. In
Page 11 and 12:
3. Implant Configuration Macroscopi
Page 13 and 14:
Bioseal Bevel/Implant Shoulder Foll
Page 15 and 16:
Tube-in-Tube Connection The long-te
Page 17 and 18:
4. Mechanics and Biomechanics Mecha
Page 19 and 20:
II. CAMLOG Concept 1. Team Concept
Page 21 and 22:
2. Treatment Concept Introduction I
Page 23 and 24:
Fixed Restorations Single Crowns Si
Page 25 and 26: Implant-Supported Bridges Implant-s
Page 27 and 28: Bar supported Dentures Bars are sui
Page 29 and 30: 2. Anamnesis Introduction The medic
Page 31 and 32: Articulator Set-Up The diagnostic c
Page 33 and 34: Planning Template A planning templa
Page 35 and 36: 5. Implant Position Verification Go
Page 37 and 38: Final Prosthesis Design The surgica
Page 39: SCREW-CYLINDER-LINE Implant The SCR
Page 42 and 43: Surgery Manual CAMLOG ® Surgery Sy
Page 44 and 45: Surgery Manual CAMLOG ® Surgery Sy
Page 46 and 47: Surgery Manual Implant Healing 4. H
Page 48 and 49: Surgery Manual SCREW-LINE Insertion
Page 73 and 74: 6. ROOT-LINE Implant Introduction T
Page 75: Incision Line The sample indication
Page 79 and 80: Paralleling Pin with Depth Marks On
Page 81 and 82: Pre-Drilling An internally irrigate
Page 83 and 84: Depth Stop During form drilling the
Page 85 and 86: Form Drilling Once pre-drilling is
Page 87 and 88: Manual thread tapping is performed
Page 89 and 90: Implant Positioning The protocol-co
Page 91 and 92: Placing the PickUp on the insertion
Page 93 and 94: Next, extract the retention screw o
Page 95 and 96: Accessories Adapter for Screw Impla
Page 97: Accessories Once the retention scre
Page 100 and 101: Surgery Manual SCREW-CYLINDER-LINE
Page 124 and 125: 116
Page 126 and 127:
Surgery Manual CYLINDER-LINE Insert
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
136
Page 146 and 147:
Surgery Manual Healing Cap Healing
Page 148 and 149:
Transfer System Introduction 10. Tr
Page 150 and 151:
Transfer System Closed Impression M
Page 152 and 153:
Transfer System Open Impression Met
Page 154 and 155:
Transfer System Open Impression Met
Page 156 and 157:
Provisional Solution Introduction 1
Page 158 and 159:
Provisional Solution Preparing the
Page 160 and 161:
General Information Torque Wrench S
Page 162 and 163:
General Information Torque Wrench C
Page 164 and 165:
156
Page 166 and 167:
Informations Materials Titanium Gra
Page 168 and 169:
160
Page 170 and 171:
162
Page 172:
➤ ➤ ISBN 978-3-13-134351-2 CAML
show all

1 Surgery CAMLOG Compendium

Create successful ePaper yourself

Delete template?

Save as template?