1 Surgery CAMLOG Compendium

More documents

Recommendations

Info

Surgery Manual SCREW-CYLINDER-LINE Insertion Implant Package All CAMLOG ® implants are double-sterile packaged. The primary package (blister) of SCREW-CYLINDER-LINE Implants contains the implant with pre-installed insertion post and mounted handle. Outer package with label Peel-back pouch (sterile) Primary package (sterile) with label (blister pack) Primary package with visible implant System information on the label 106 Opened primary package with implant and mounted handle Cover screw located in the handle
Implant Positioning The protocol-compliant implant position (form drilling with depth stop) is achieved when the cylindrical machined implant shoulder extends 0.4 mm above the crestal bone and one of the 3 groove marks indicates the specified prosthetic position. If it was decided to set the drilling depth for the implants individually by removing the depth stop during form drilling, this should be kept in mind during implant insertion. It is possible to individually position the 1.6 mm implant shoulder vertically to match the drill hole. You should make sure, however, to position the Bioseal Bevel circularly in the cortical bone. Mark Cam Groove Vestibular orientation of the groove Surgery Manual SCREW-CYLINDER-LINE Insertion Driver Insertion post Implant Groove Positioning Marks are inscribed on the drivers for the SCREW-CYLINDER-LINE Implants that match the three grooves on the CAMLOG connection. These permit you to check the groove positions during the insertion and their orientation as required for the prosthesis. If the dental technician has not indicated the groove position, a vestibular orientation is advantageous in most cases since the abutment angle originates at a groove. Note: keep in mind during positioning of the grooves that turning to the next groove position (120°) will cause the screw implant to be inserted about 0.2 mm deeper. 107
Page 1:
CAMLOG Compendium 1 Surgery
Page 4 and 5:
CAMLOG Compendium | 1 Surgery Bibli
Page 6 and 7:
CAMLOG Compendium | 1 Surgery 4. Pr
Page 9 and 10:
I. General System Information 1. In
Page 11 and 12:
3. Implant Configuration Macroscopi
Page 13 and 14:
Bioseal Bevel/Implant Shoulder Foll
Page 15 and 16:
Tube-in-Tube Connection The long-te
Page 17 and 18:
4. Mechanics and Biomechanics Mecha
Page 19 and 20:
II. CAMLOG Concept 1. Team Concept
Page 21 and 22:
2. Treatment Concept Introduction I
Page 23 and 24:
Fixed Restorations Single Crowns Si
Page 25 and 26:
Implant-Supported Bridges Implant-s
Page 27 and 28:
Bar supported Dentures Bars are sui
Page 29 and 30:
2. Anamnesis Introduction The medic
Page 31 and 32:
Articulator Set-Up The diagnostic c
Page 33 and 34:
Planning Template A planning templa
Page 35 and 36:
5. Implant Position Verification Go
Page 37 and 38:
Final Prosthesis Design The surgica
Page 39:
SCREW-CYLINDER-LINE Implant The SCR
Page 42 and 43:
Surgery Manual CAMLOG ® Surgery Sy
Page 44 and 45:
Surgery Manual CAMLOG ® Surgery Sy
Page 46 and 47:
Surgery Manual Implant Healing 4. H
Page 48 and 49:
Surgery Manual SCREW-LINE Insertion
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65: Surgery Manual SCREW-LINE Insertion
Page 73 and 74: 6. ROOT-LINE Implant Introduction T
Page 75 and 76: Incision Line The sample indication
Page 77 and 78: 13 mm 11 mm 9 mm 13 mm 11 mm 9 mm 1
Page 79 and 80: Paralleling Pin with Depth Marks On
Page 81 and 82: Pre-Drilling An internally irrigate
Page 83 and 84: Depth Stop During form drilling the
Page 85 and 86: Form Drilling Once pre-drilling is
Page 87 and 88: Manual thread tapping is performed
Page 89 and 90: Implant Positioning The protocol-co
Page 91 and 92: Placing the PickUp on the insertion
Page 93 and 94: Next, extract the retention screw o
Page 95 and 96: Accessories Adapter for Screw Impla
Page 97: Accessories Once the retention scre
Page 100 and 101: Surgery Manual SCREW-CYLINDER-LINE
Page 124 and 125: 116
Page 126 and 127: Surgery Manual CYLINDER-LINE Insert
Page 144 and 145: 136
Page 146 and 147: Surgery Manual Healing Cap Healing
Page 148 and 149: Transfer System Introduction 10. Tr
Page 150 and 151: Transfer System Closed Impression M
Page 152 and 153: Transfer System Open Impression Met
Page 154 and 155: Transfer System Open Impression Met
Page 156 and 157: Provisional Solution Introduction 1
Page 158 and 159: Provisional Solution Preparing the
Page 160 and 161: General Information Torque Wrench S
Page 162 and 163: General Information Torque Wrench C
Page 164 and 165:
156
Page 166 and 167:
Informations Materials Titanium Gra
Page 168 and 169:
160
Page 170 and 171:
162
Page 172:
➤ ➤ ISBN 978-3-13-134351-2 CAML
show all

1 Surgery CAMLOG Compendium

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?