1 Surgery CAMLOG Compendium

More documents

Recommendations

Info

General System Information Implant Configuration External Configuration <strong>CAMLOG</strong> ® implants SCREW-LINE, ROOT- LINE and SCREW-CYLINDER-LINE with the Promote ® surface have a cylindrical machined portion 1.6 mm high in the coronal area (1). A rough machined chamfer - the Bioseal Bevel (height 0.4 mm) - is attached to this apically (2). Below it is the self-tapping thread of the SCREW-LINE, ROOT-LINE or SCREW- CYLINDER-LINE implants (3) with the Promote ® surface. In the case of the CYLINDER-LINE implants, a TPS (titanium plasma-sprayed) surface is provided. Internal Configuration Starting from the coronal implant edge (4), all implants have three symmetrical grooves (width 0.5 or 0.7 mm, depth 1.2 mm, 120° offset) in the upper cylindrical area (5). The abutment cams lock into these grooves. Beneath this area, an upper inner thread is found (6), on which the cover screw, healing caps, bar abutments, and male inserts of different prosthetic caps can be screwed. Apical to the thread is a short cylindrical part to which the abutment "tube" is attached (7). After another 60° offset, there follows apically a second inner thread (8) onto which the abutment screws M 1.6 or 2.0 are fastened. 4 1 2 3 On the SCREW-LINE Implant with Promote ® plus surface, the machined part measures 0.4 mm. 4 5 6 7 8
Bioseal Bevel/Implant Shoulder Following the protocol-conformal insertion of the implant, the implant shoulder lies approx. 0.4 mm above the bone level. Drilling irregularities between the implant drill hole and implant are totally excluded by the chamfer (Bioseal Bevel) beneath the implant shoulder which matches the profile of the drill hole. A biological width of approx. 2 mm remains (1 mm connective tissue adaptation and upon this an approx. 1-mm junction epithelial attachment) following protocol-conformal insertion of the implants with the Promote ® surface and TPS coating, and following exposure and a minor bone adaptation of approx. 1 mm apically. SCREW-LINE Implants with Promote ® plus surface are likewise inserted so as to leave a 0.4 mm projection above the bone level. During the insertion and exposure, the periosteum should be removed only in the implant penetration area. Promote ® and TPS surface Promote ® plus surface General System Information Implant Configuration 5
Page 1: CAMLOG Compendium 1 Surgery
Page 4 and 5: CAMLOG Compendium | 1 Surgery Bibli
Page 6 and 7: CAMLOG Compendium | 1 Surgery 4. Pr
Page 9 and 10: I. General System Information 1. In
Page 11: 3. Implant Configuration Macroscopi
Page 15 and 16: Tube-in-Tube Connection The long-te
Page 17 and 18: 4. Mechanics and Biomechanics Mecha
Page 19 and 20: II. CAMLOG Concept 1. Team Concept
Page 21 and 22: 2. Treatment Concept Introduction I
Page 23 and 24: Fixed Restorations Single Crowns Si
Page 25 and 26: Implant-Supported Bridges Implant-s
Page 27 and 28: Bar supported Dentures Bars are sui
Page 29 and 30: 2. Anamnesis Introduction The medic
Page 31 and 32: Articulator Set-Up The diagnostic c
Page 33 and 34: Planning Template A planning templa
Page 35 and 36: 5. Implant Position Verification Go
Page 37 and 38: Final Prosthesis Design The surgica
Page 39: SCREW-CYLINDER-LINE Implant The SCR
Page 42 and 43: Surgery Manual CAMLOG ® Surgery Sy
Page 44 and 45: Surgery Manual CAMLOG ® Surgery Sy
Page 46 and 47: Surgery Manual Implant Healing 4. H
Page 48 and 49: Surgery Manual SCREW-LINE Insertion
Page 62 and 63:
Surgery Manual SCREW-LINE Insertion
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 73 and 74:
6. ROOT-LINE Implant Introduction T
Page 75 and 76:
Incision Line The sample indication
Page 77 and 78:
13 mm 11 mm 9 mm 13 mm 11 mm 9 mm 1
Page 79 and 80:
Paralleling Pin with Depth Marks On
Page 81 and 82:
Pre-Drilling An internally irrigate
Page 83 and 84:
Depth Stop During form drilling the
Page 85 and 86:
Form Drilling Once pre-drilling is
Page 87 and 88:
Manual thread tapping is performed
Page 89 and 90:
Implant Positioning The protocol-co
Page 91 and 92:
Placing the PickUp on the insertion
Page 93 and 94:
Next, extract the retention screw o
Page 95 and 96:
Accessories Adapter for Screw Impla
Page 97:
Accessories Once the retention scre
Page 100 and 101:
Surgery Manual SCREW-CYLINDER-LINE
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
116
Page 126 and 127:
Surgery Manual CYLINDER-LINE Insert
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
136
Page 146 and 147:
Surgery Manual Healing Cap Healing
Page 148 and 149:
Transfer System Introduction 10. Tr
Page 150 and 151:
Transfer System Closed Impression M
Page 152 and 153:
Transfer System Open Impression Met
Page 154 and 155:
Transfer System Open Impression Met
Page 156 and 157:
Provisional Solution Introduction 1
Page 158 and 159:
Provisional Solution Preparing the
Page 160 and 161:
General Information Torque Wrench S
Page 162 and 163:
General Information Torque Wrench C
Page 164 and 165:
156
Page 166 and 167:
Informations Materials Titanium Gra
Page 168 and 169:
160
Page 170 and 171:
162
Page 172:
➤ ➤ ISBN 978-3-13-134351-2 CAML
show all

1 Surgery CAMLOG Compendium

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?