Catalog PM 21 2013 - Siemens Industry, Inc.

More documents

Recommendations

Info

© Siemens AG 2013 SINAMICS S120 drive system Power Modules and line-side components Air-cooled Power Modules in chassis format ■ Technical specifications Air-cooled Power Module in chassis format 6SL3310-1TE3... Line connection voltage 380 … 480 V 3 AC ±10 % (in operation -15 % < 1 min) (up to 2000 m (6562 ft) above sea level) Line Grounded TN/TT systems and non-grounded IT systems Line frequency 47 … 63 Hz Line power factor with a 3 AC connection voltage and rated power • Fundamental power factor (cos ϕ 1 ) > 0.96 •Total (λ) 0.75 … 0.93 Overvoltage category Class III to EN 60664-1 Precharging frequency 1× every 300 s of the DC link, max. DC link voltage, approx. 1.35 × line voltage Output frequency • Control type Servo 0 … 650 Hz 1) • Control type Vector 0 … 300 Hz 1) • Control type V/f 0 … 600 Hz 1) Electronics power supply 24 V DC -15 %/+20 % Main contactor control Terminal strip X9/5-6 Radio interference suppression 240 V AC/ max. 8 A 30 V DC/ max. 1A • Standard (in combination with line reactor) Category C3 to EN 61800-3 • With line filter and line reactor Category C2 to EN 61800-3 Type of cooling Forced air cooling by means of built-in fan Permissible ambient and coolant temperature (air) during operation for line-side components, Line Modules and Motor Modules Installation altitude Conformity Approvals, according to Safety Integrated 0 … 40 °C (32 … 104 °F) without derating, > 40 … 55 °C (104 …131 °F) see derating characteristics Up to 2000 m (6562 ft) above sea level without derating, > 2000 ... 4000 m (6562 ... 13124 ft) above sea level, see derating characteristics CE (Low Voltage and EMC Directives) cULus Safety Integrity Level 2 (SIL 2) acc. to IEC 61508, Performance Level d (PLd) acc. to ISO 13849-1 and Control Category 3 acc. to ISO 13849-1 or EN 954-1. For further information, see chapter Safety Integrated. 3 1) Note the correlation between max. output frequency, pulse frequency and current derating. For further information see chapter System description – Dimensioning. Siemens PM 21 · 2013 3/49
SINAMICS S120 drive system Power Modules and line-side components Air-cooled Power Modules in chassis format ■ Technical specifications (continued) © Siemens AG 2013 3 Line voltage Air-cooled Power Module in chassis format 380 … 480 V 3 AC 6SL3310- 1TE32-1AA3 6SL3310- 1TE32-6AA3 6SL3310- 1TE33-1AA3 6SL3310- 1TE33-8AA3 6SL3310- 1TE35-0AA3 Output current • Rated current I rated A 210 260 310 380 490 • Base-load current I L A 205 250 302 370 477 • Base-load current I H A 178 233 277 340 438 • For S6 duty (40 %) I S6 A 230 285 340 430 540 • I max A 307 375 453 555 715 Type rating 1) • Based on I rated kW (HP) 110 (150) 132 (200) 160 (250) 200 (300) 250 (400) • Based on I H kW (HP) 90 (150) 110 (150) 132 (200) 160 (250) 200 (350) Rated pulse frequency kHz 2 2 2 2 2 Current requirement A 0.8 0.8 0.9 0.9 0.9 with 24 V DC, max. 2) Power loss, max. kW 2.54 3.36 4.07 4.67 5.96 Cooling air requirement m 3 /s (ft 3 /s) 0.17 (6.00) 0.23 (8.12) 0.36 (12.7) 0.36 (12.7) 0.36 (12.7) Sound pressure level dB 66/67 68/72 68/72 68/72 68/72 L pA (1 m) at 50/60 Hz Rated input current A 229 284 338 395 509 Line connection U1, V1, W1 Flat connector for M10 screw Flat connector for M10 screw Flat connector for M10 screw Flat connector for M10 screw • Conductor cross-section, max. mm 2 2 × 185 2 × 185 2 × 240 2 × 240 2 × 240 DC link connection DCPA, DCNA (option Braking Module) Flat connector for M8 screw Flat connector for M8 screw Flat connector for M8 screw Flat connector for M8 screw • Conductor cross-section, max. mm 2 1 × 35 1 × 35 1 × 50 1 × 50 1 × 50 DC link connection DCPS, DCNS Flat connector for M8 screw Flat connector for M8 screw Flat connector for M8 screw Flat connector for M8 screw • Conductor cross-section, max. mm 2 1 × 35 1 × 35 1 × 70 1 × 70 1 × 70 Motor connection U2, V2, W2 Flat connector for M10 screw Flat connector for M10 screw Flat connector for M10 screw Flat connector for M10 screw Flat connector for M10 screw Flat connector for M8 screw Flat connector for M8 screw Flat connector for M10 screw • Conductor cross-section, max. mm 2 2 × 185 2 × 185 2 × 240 2 × 240 2 × 240 PE connection Flat connector for M10 screw Flat connector for M10 screw Flat connector for M10 screw Flat connector for M10 screw Flat connector for M10 screw • Conductor cross-section, max. mm 2 2 × 185 2 × 185 2 × 240 2 × 240 2 × 240 Motor cable length 3) , max. • Shielded m (ft) 300 (984) 300 (984) 300 (984) 300 (984) 300 (984) • Unshielded m (ft) 450 (1476) 450 (1476) 450 (1476) 450 (1476) 450 (1476) Degree of protection IP20 IP20 IP20 IP20 IP20 Dimensions • Width mm (in) 326 (12.8) 326 (12.8) 326 (12.8) 326 (12.8) 326 (12.8) •Height mm (in) 1400 (55.1) 1400 (55.1) 1533 (60.3) 1533 (60.3) 1533 (60.3) •Depth mm (in) 356 (14.0) 4) 356 (14.0) 4) 549 (21.6) 549 (21.6) 549 (21.6) Frame size FX FX GX GX GX Weight, approx. kg (lb) 104 (229) 104 (229) 162 (357) 162 (357) 162 (357) 1) Nominal HP based on asynchronous (induction) motors and 460 V 3 AC. For specific sizing select drive based on motor nameplate current and overload. 2) Current consumption of Power Module only. If a Control Unit is supplied with 24 V DC over the Power Module, its current consumption must be added. 3) Motor cable length, max. 100 m (328 ft) (shielded) in conjunction with a line filter to maintain the limit values of EN 61800-3 Category C2. 4) Depth = 421 mm (16.6 in) including front cover when CU310-2/D410-2 Control Unit is installed. 3/50 Siemens PM 21 · 2013
Page 1 and 2: © Siemens AG 2013 SIMOTION, SINAMI
Page 3 and 4: © Siemens AG 2013 Motion Control S
Page 5 and 6: SINAMICS S120 drive system Overview
Page 7 and 8: SINAMICS S120 drive system System o
Page 13 and 14: SINAMICS S120 drive system © Sieme
Page 15 and 16: SINAMICS S120 drive system Control
Page 27 and 28: SINAMICS S120 drive system Engineer
Page 29 and 30: SINAMICS S120 drive system Engineer
Page 31 and 32: SINAMICS S120 drive system Power Mo
Page 51: SINAMICS S120 drive system Power Mo
Page 65 and 66: SINAMICS S120 drive system Line Mod
Page 103 and 104:
SINAMICS S120 drive system Line Mod
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
SINAMICS S120 drive system Motor Mo
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
SINAMICS S120 drive system DC link
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
SINAMICS S120 drive system Load-sid
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
SINAMICS S120 drive system Suppleme
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
SINAMICS S120 drive system Encoder
Page 247 and 248:
Page 249 and 250:
Page 251:
show all

Catalog PM 21 2013 - Siemens Industry, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?