Stober 1 Servo Gear Units

More documents

Recommendations

Info

F Series: OFFSET – Versatile Outputs “A” Hollow Output with “NG” Foot Mounting — All Sizes s3 Dia. x t3 Deep (4 Holes as shown) Side 3 and Side 4) b4 Side 3 Side 4 See Rubber Buffer Option below for mounting torque arms. a0 b3 n1 c1 B Table 1 Dimensions (mm) Unit a0 B b3 b4 c1 n1 s3 t3 F1 50 142 40 140 29 10 M6 11 F2 64 176 55 175 33.5 10.5 M8 13 F3 72 204 60 200 37.5 12.5 M10 16 F4 87 228 70 220 37.5 12.5 M10 16 F6 108 262 85 270 46.5 15.5 M12 19 Rubber Buffer Option sd (+0.5/-0.0) ad Hd B ld ld Table 2 “Rubber Buffer Dimensions (mm) ad1 Dd Unit Part No. ad ad1 B Dd Hd ld sd F1 25192 35 150 142 30 14 15 11 F2 25192 40 181 176 30 25 15 11 F3 25193 45 205 204 40 24.5 20 12.5 F4 25193 45 228 228 40 26 20 12.5 F6 25194 55 270 262 60 26 30 21 Order two (2) rubber buffers for each unit. Torque arms are not supplied by STOBER. 160 Servo Gear Units V.28 800.711.3588 • www.stober.com
Dimensional Data “S” Shrink Ring with “G” Pitch Circle Diameter (PCD) Tapped Holes — All SIzes c Motor Plate Thickness* X C D m i2 f s4 Dia. x t4 Deep on e Bolt Circle (F102 — F403) cd s4 Dia. x t4 Deep on e Bolt Circle (F602 and F603) * See Motor Mounting Plate Option, page 143 for details. Table 1 Shaft Dimensions (mm) Unit B B1 b j6 cd d h9 D Bore d H7 Shaft d1 h9 d3 d4 F1 145 87 70 20 20 35 20 20 24 20.5 F2 180 105 95 22 25 45 25 25 30 25.5 F3 206 120 110 30 30 50 30 30 36 30.5 F4 230 135 110 30 40 55 40 40 50 40.5 F6 265 166 130 35 50 70 50 50 62 50.5 Table 2 Dimensions (mm) Unit DS e e2 f H h Hn i2 IHS m 2 m 3 m 4 m 5 n s4 t4 F1 50 85 58 2.5 238 74 176 6.5 146 20 31 25 26 102 M8x1.25 13 F2 60 115 72 3 299 93 224 8 175 20 37 25 32 131 M8x1.25 13 F3 72 130 78 3.5 335.5 106 255.5 8.5 192 25 37 30 32 149.5 M10x1.5 16 F4 90 130 83 3.5 370 116 285 2) 8.5 210 40 45 45 40 169 1) M10x1.5 16 F6 106 165 102 3.5 433 137 333 10.5 248 40 47 45 42 196 M10x1.5 16 1) For F303, Hn is 219 with ME20 and n is 113; For F403, Hn is 248 with ME20 and n is 132 Table 3 Dimensions (mm) Unit Square To Fit Motor* DS M5 Dia. x 9 mm Deep On e2 Bolt Circle (Optional Cover) ME10 ME20 ME30 ME40 Approx. C m C m C m C m Wt. lbs. F102 144 104 158 108 — — — — 38 F202 163 123 177 127 189 129 — — 51 F203 200 160 — — — — — — 64 F302 178 138 192 142 204 144 — — 67 F303 215 175 235 185 — — — — 73 F402 — — 207 157 219 159 250 162 84 F403 230 190 250 200 — — — — 91 F602 — — 240 190 252 192 283 195 165 F603 — — 283 233 — — — — 177 B1 n b Hn B d3 d1 d1 See Installation Guide for shrink ring installation. Table 4 Motor Adapter Dimensions (mm) Motor Adapter h H Thickness 3) c Min. 22.5° IHS m 5 m 2 d4 d D m 3 Motor Shaft d2 Max. 2) m 4 X Wt. lbs. ME10 21 19 40 5 ME20 24 32 50 8 ME30 25 38 60 12 ME40 33 48 88 18 2) If an adapter bushing is required it will be supplied as a component of the motor mounting plate. 3) Motor plate maximum thickness (c) will vary with motor shaft length but will not be less than shown. For approximate weight, add unit weight from Table 3 and adapter weight from Table 4. d F Series: OFFSET – Versatile Outputs 800.711.3588 • www.stober.com Servo Gear Units V.28 161
Page 1 and 2:
Servo Gear Units Geared to a higher
Page 3 and 4:
Geared to a higher standard Conten
Page 5 and 6:
Geared to a higher standard Servic
Page 7 and 8:
Unique STOBER Quality and Design Fe
Page 9 and 10:
Overview Selection At-a-Glance Righ
Page 11 and 12:
Overview Selection At-a-Glance RIGH
Page 13 and 14:
Gearhead Sizing to your Specific Ap
Page 15 and 16:
Overview Selection Options At-a-Gla
Page 17 and 18:
Overview P/PA Series Motor Mounting
Page 19 and 20:
Overview P/PA No Load Running Torqu
Page 21 and 22:
Selection Data P2 Exact Ratio (i) O
Page 23 and 24:
Selection Data Exact Ratio (i) P/PA
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
P9 Exact Ratio (i) Output Torque Mo
Page 45 and 46:
Dimensional Data Large Input Option
Page 47 and 48:
Page 49 and 50:
Overview Note: Overview data is gen
Page 51 and 52:
Overview PH Series Permissible Moto
Page 53 and 54:
Selection Data Exact Ratio (i) Outp
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Dimensional Data Table 1 Dimensions
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Overview Permissible Motor Tilting
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Dimensional Data PE with MAL Input
Page 103 and 104:
Page 105 and 106:
Overview C40 C50 C61 C71 C81 C91 2
Page 107 and 108:
Overview C Series Lubrication Maint
Page 109 and 110: Selection Data Reducer Ratio (i) No
Page 131 and 132: Dimensional Data SMS Reducer Option
Page 133 and 134: Dimensional Data Table 1 Dimensions
Page 141 and 142: Overview Selection Options At-a-Gla
Page 143 and 144: Overview F Series Motor Mounting Pl
Page 145 and 146: Overview Overhung Load Calculations
Page 155 and 156: Dimensional Data “V” Shaft Outp
Page 157 and 158: Dimensional Data “W” Double Bus
Page 159: Dimensional Data “A” Hollow Out
Page 163 and 164: Overview Selection Options At-a-Gla
Page 165 and 166: Overview K51 K61 K71 K81 K91 K101 3
Page 167 and 168: Overview K/KL Series Output Options
Page 193 and 194: Dimensional Data KL Series with “
Page 199 and 200: Dimensional Data Table 1 K Series U
Page 211 and 212:
Dimensional Data Table 1 K Series U
Page 213 and 214:
Dimensional Data Optional “F” R
Page 215 and 216:
Page 217 and 218:
Overview PK Performance Overview PK
Page 219 and 220:
Overview PKX/PK Series Motor Mounti
Page 221 and 222:
Overview PKX/PK Output Bearing Opti
Page 223 and 224:
Selection Data Exact Ratio (i) Nomi
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Selection Data Reducer Ratio (i) No
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Dimensional Data PKX Series — Two
Page 247 and 248:
Dimensional Data Motor Mounting Pla
Page 249 and 250:
Page 251 and 252:
Overview PHK Performance Overview S
Page 253 and 254:
Overview PHKX/PHK/PHQK Series Motor
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Reducer Ratio (i) Nominal 1) M2N Ou
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Overview KS Series Motor Mounting P
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Overview IP69K/STAINLESS STEEL KSS
Page 315 and 316:
Overview IP69K/STAINLESS STEEL KSS
Page 317 and 318:
Selection Data IP69K/STAINLESS STEE
Page 319 and 320:
Selection Data IP69K/STAINLESS STEE
Page 321 and 322:
Dimensional Data IP69K/STAINLESS ST
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Technical Reference C Series Solid
Page 329 and 330:
Technical Reference Values and Symb
Page 331 and 332:
Other Products from STOBER ServoSto
Page 333:
STOBER Servo Gear Units V.28
show all

Stober 1 Servo Gear Units

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?