Stober 1 Servo Gear Units

More documents

Recommendations

Info

KSS Series: RIGHT ANGLE — Solid Shaft/Hollow Output “V” Solid Shaft Output with “NG” Foot Mount Housing u t c Motor Mounting Plate Thickness* s6 c6 C m m1 d i2 B2 a4 l e6 Side 2 i1 a6 b6 n Side 5 b5 b7 d h H * See Motor Mounting Plate Option, page 315 for details. s Dia. Side 1 b5 n2 n3 a0 n4 b4 Table 1 KSS Series – “V” Solid Shaft Output with “NG” Foot Mount Housing – Dimensions (mm) Unit a0 a4 B2 b4 b5 b7 C c6 H h n4 KSS102VNG 115 115 106 90 30 75 256.5 85.5 126 60 140 KSS202VNG 171 126 134 115 35 95 299 104 164 78 196 KSS302VNG 171 132 146 130 35 105 327.5 102.5 179.5 87.5 196 Table 2 KSS Series – “V” Solid Shaft Output with “NG” Foot Mount Housing – Dimensions (mm) Unit i2 l l1 m m1 n n2 n3 s Wt. lbs. KSS102VNG 59 50 4 111 60 36 38.1 12.7 8.4 29 KSS202VNG 66 60 4 130 65 46 38.1 12.7 10 40 KSS302VNG 66 60 4 150 75 53 38.1 12.7 10 55 All weights are approximate. Table 3 “V” Solid Shaft Output — Standard Sizes Inches Unit d t u – Key KSS1 1.000 1.11 1/4 x 1/4 x 1-9/16 KSS2 1.250 1.36 1/4 x 1/4 x 1-15/16 KSS3 1.250 1.36 1/4 x 1/4 x 1-15/16 Table 4 Servo Motor Adapter Flange (mm) Unit a6 b6 e6 s6 KSS1 112 80 100 6.4 KSS2 KSS3 112 143 112 143 180 80 110 80 110 130 100 130 100 130 165 6.5 8.4 6.4 8.4 10.5 322 Servo Gear Units V.28 800.711.3588 • www.stober.com
Dimensional Data IP69K/STAINLESS STEEL “A” Hollow Bore Output with “F” Round Flange Housing c Motor Mounting Plate Thickness* C th uh lh s6 c6 m m1 dh B2 f1 e6 a6 b6 n a1 Dh b H * See Motor Mounting Plate Option, page 315 for details. s1 Dia. Slot 1) on e1 Bolt Circle c1 c2 B h 1 2 le lh Table 2 KSS Series – “A” Hollow Output with “F” Round Flange Housing – Dimensions (mm) Unit e1 800.711.3588 • www.stober.com Min. Max. 1) f1 h le m m1 n s1 KSS102AF 149.2 – 3 60 98 111 60 36 8.5 29 KSS202AF 190 203.2 3 65 113 130 65 46 10.5 40 KSS302AF 190 203.2 3 75 125 150 75 53 10.5 55 1) KSS1 mounting bolt hole is not a slot. All weights are approximate. Table 3 “A” Hollow Bore Output — Standard Sizes Inches Unit dh th UA 1 KSS1 1.000 1.11 0.250 1/2 – 13 KSS2 1.250 1.37 0.250 5/8 – 11 KSS3 1.375 1.52 0.312 5/8 – 11 1. Removal Bolt — not supplied. Must be smaller than mounting bolt. See Installation Guide for details. 2. Mounting Bolt See installation guide for installation of hollow output. Table 1 KSS Series – “A” Hollow Output with “F” Round Flange Housing – Dimensions (mm) Unit a1 lh B B2 b C c1 c2 c6 Dh KSS102AF 171.5 120 90 106 75 256.5 14 38.1 82.5 40 KSS202AF 222 148 112 134 95 299 14 38.1 104 50 KSS302AF 222 160 140 146 95 327.5 14 38.1 102.5 50 1) KSS1 mounting bolt hole is not a slot Table 4 Servo Motor Adapter Flange (mm) Unit a6 b6 e6 s6 KSS1 112 80 100 6.4 KSS2 KSS3 112 143 112 143 180 80 110 80 110 130 100 130 100 130 165 6.5 8.4 Wt. lbs. 6.4 8.4 10.5 Servo Gear Units V.28 323 KSS Series: RIGHT ANGLE — Solid Shaft / Hollow Output
Page 1 and 2:
Servo Gear Units Geared to a higher
Page 3 and 4:
Geared to a higher standard Conten
Page 5 and 6:
Geared to a higher standard Servic
Page 7 and 8:
Unique STOBER Quality and Design Fe
Page 9 and 10:
Overview Selection At-a-Glance Righ
Page 11 and 12:
Overview Selection At-a-Glance RIGH
Page 13 and 14:
Gearhead Sizing to your Specific Ap
Page 15 and 16:
Overview Selection Options At-a-Gla
Page 17 and 18:
Overview P/PA Series Motor Mounting
Page 19 and 20:
Overview P/PA No Load Running Torqu
Page 21 and 22:
Selection Data P2 Exact Ratio (i) O
Page 23 and 24:
Selection Data Exact Ratio (i) P/PA
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
P9 Exact Ratio (i) Output Torque Mo
Page 45 and 46:
Dimensional Data Large Input Option
Page 47 and 48:
Page 49 and 50:
Overview Note: Overview data is gen
Page 51 and 52:
Overview PH Series Permissible Moto
Page 53 and 54:
Selection Data Exact Ratio (i) Outp
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Dimensional Data Table 1 Dimensions
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Overview Permissible Motor Tilting
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Dimensional Data PE with MAL Input
Page 103 and 104:
Page 105 and 106:
Overview C40 C50 C61 C71 C81 C91 2
Page 107 and 108:
Overview C Series Lubrication Maint
Page 109 and 110:
Selection Data Reducer Ratio (i) No
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Dimensional Data SMS Reducer Option
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Overview F Series Motor Mounting Pl
Page 145 and 146:
Overview Overhung Load Calculations
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Dimensional Data “V” Shaft Outp
Page 157 and 158:
Dimensional Data “W” Double Bus
Page 159 and 160:
Dimensional Data “A” Hollow Out
Page 161 and 162:
Dimensional Data “S” Shrink Rin
Page 163 and 164:
Page 165 and 166:
Overview K51 K61 K71 K81 K91 K101 3
Page 167 and 168:
Overview K/KL Series Output Options
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Dimensional Data KL Series with “
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Dimensional Data Table 1 K Series U
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Dimensional Data Optional “F” R
Page 215 and 216:
Page 217 and 218:
Overview PK Performance Overview PK
Page 219 and 220:
Overview PKX/PK Series Motor Mounti
Page 221 and 222:
Overview PKX/PK Output Bearing Opti
Page 223 and 224:
Selection Data Exact Ratio (i) Nomi
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Dimensional Data PKX Series — Two
Page 247 and 248:
Dimensional Data Motor Mounting Pla
Page 249 and 250:
Page 251 and 252:
Overview PHK Performance Overview S
Page 253 and 254:
Overview PHKX/PHK/PHQK Series Motor
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272: Selection Data Exact Ratio (i) Nomi
Page 279 and 280: Reducer Ratio (i) Nominal 1) M2N Ou
Page 281 and 282: Selection Data Reducer Ratio (i) No
Page 293 and 294: Dimensional Data Table 1 Dimensions
Page 299 and 300: Overview Selection Options At-a-Gla
Page 301 and 302: Overview KS Series Motor Mounting P
Page 303 and 304: Selection Data Exact Ratio (i) Outp
Page 305 and 306: Selection Data Exact Ratio (i) Outp
Page 313 and 314: Overview IP69K/STAINLESS STEEL KSS
Page 315 and 316: Overview IP69K/STAINLESS STEEL KSS
Page 317 and 318: Selection Data IP69K/STAINLESS STEE
Page 319 and 320: Selection Data IP69K/STAINLESS STEE
Page 321: Dimensional Data IP69K/STAINLESS ST
Page 325 and 326: Dimensional Data IP69K/STAINLESS ST
Page 327 and 328: Technical Reference C Series Solid
Page 329 and 330: Technical Reference Values and Symb
Page 331 and 332: Other Products from STOBER ServoSto
Page 333: STOBER Servo Gear Units V.28
show all

Stober 1 Servo Gear Units

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?