Stober 1 Servo Gear Units

Dimensional Data
Table 1 Dimensions (mm)
Unit a1 B b1 h7* b2 c1 df H7* ef e1 f1 H H1 h i2
PH5_K1 145 56 110 +0.000/-0.035 120 8 40 +0.025/-0.0 63 135 10 160 – 60 29
PH7_K1 179 56 140 +0.000/-0.040 152 10 50 +0.025/-0.0 80 168 12 160 – 60 38
PH7_K2 179 70 140 +0.000/-0.040 152 10 50 +0.025/-0.0 80 168 12 190 – 65 38
PH8_K2 247 70 200 +0.000/-0.046 212 12 80 +0.030/-0.0 125 233 15 190 – 65 50
PH8_K3 247 76 200 +0.000/-0.046 212 12 80 +0.030/-0.0 125 233 15 213 – 75 50
PH9_K5 300 96 255 +0.000/-0.052 255 18 90 +0.035/-0.0 140 280 20 260 312 160 66
PH10_K6 330 103.5 285 +0.000/-0.052 285 20 95 +0.035/-0.0 160 310 20 310 362 190 75
Table 2 Dimensions (mm)
Unit k L l2 l4 lh m1 o r s1 sf sf1 H7* tf tf1 v h7*
PH5_K1 70 201 6 6 6 60 116 0.020 5.5 M6x1.00 M6x1.00 +0.012/-0.000 11 7 80 +0.000/-0.030
PH7_K1 88 214 6 6 6 60 120 0.025 6.6 M8x1.25 M8x1.25 +0.015/-0.000 14 7 100 +0.000/-0.035
PH7_K2 88 242 6 6 6 65 134 0.025 6.6 M8x1.25 M8x1.25 +0.015/-0.000 14 7 100 +0.000/-0.035
PH8_K2 126 284.5 8 8 8 65 164.5 0.030 9 M10x1.50 M10x1.50 +0.015/-0.000 18 10 160 +0.000/-0.040
PH8_K3 126 298 8 8 8 75 172 0.030 9 M10x1.50 M10x1.50 +0.015/-0.000 18 10 160 +0.000/-0.040
PH9_K5 145 358.5 11 12 12 100 196.5 0.030 13.5 M16x2.00 – 24 – 180 +0.000/-0.040
PH10_K6 126 393.5 15 15 10 120 215 0.040 13.5 M20x 2.25 – 30 – 200 +0.000/-0.046
Motor Mounting Plate
Table 3 Dimensions (mm)
Base
Module
Table 4 Dimensions (mm)
Motor Adapter
Code
Thickness 2)
c Min.
Motor Adapter Code
Motor Shaft
d2
Max. 1) X Wt. lbs.
ME10 21 19 40 5
ME20 24 32 50 8
ME30 25 38 60 15
ME40 33 48 88 28
ME50 43 60 88.1 42
1) If an adapter bushing is required it will be supplied as a component of the motor mounting plate.
2) Motor plate maximum thickness (L9) will vary with motor shaft length but will not be less than shown.
* h7 = existing values; H7 = permissible values
ME10 ME20 ME30 ME40 ME50 Wt.
C m n C m n C m n C m n C m n lbs.
PH5_K1 236.5 124 36 240.5 128 36 — — — — — — — — — 43
PH7_K1 253.5 124 36 263.5 128 36 — — — — — — — — — 53
PH7_K2 278.5 143 46 286.5 147 46 296.5 149 46 — — — — — — 69
PH8_K2 310.5 143 46 316.5 147 46 330.5 149 46 — — — — — — 116
PH8_K3 332.5 163 52.5 342.5 169 52.5 352.5 169 52.5 — — — — — — 134
PH9_K5 — — — — — — 374 174 15 376 177 15 — — — 213
PH10_K6 — — — 401 191 18 403 193 18 405 196 18 420 210 18 310
PHKX/PHK/PHQK Series: RIGHT ANGLE – Flange Output
800.711.3588 • www.stober.com Servo Gear Units V.28 295