VF-FS1 Industrial Inverter - Toshiba

More documents

Recommendations

Info

6 Setting of switching terminals F-16 E6581381 The terminal for switching to motor 2 needs to be set, since this function is not assigned under the default setting. Assign this function to an idle terminal. The parameters to be switched depend on the particular identification number of the input terminal selection function. 5 AD2 Input terminal function number 39 <strong>VF</strong>2 40 MOT2 61 OCS2 OFF OFF OFF OFF ON OFF OFF OFF Parameters used and applicable parameters Default setting: , , , , , , , , → , → , → OFF OFF OFF ON → OFF ON OFF OFF - - ON - = , → , → , → , → = , → , → , → , → , → , → , → , → Note: The parameters , , , and cannot be switched during operation. You need to stop operation when switching them. 6.5 Frequency priority selection 6.5.1 Using a frequency command according to the particular situation : Frequency setting mode selection 1 : Frequency priority selection : Speed setting mode selection 2 • Function These parameters are used to switch between two types of frequency command signals. • Setting by parameters • Switching by frequency • Switching via terminal board input
F-17 E6581381 [Parameter setting] Title Function Adjustment range Default setting Frequency setting mode selection 1 Frequency priority selection Frequency setting mode selection 2 1: VIA 2: VIB 3: Operation panel 4: RS485 communication 5: UP/DOWN from external contact 0: (Switchable to by the input terminal) 1: ( for output frequencies equal to or lower than 1.0 Hz) 1: VIA 2: VIB 3: Operation panel 4: RS485 communication 5: UP/DOWN from external contact 1) External switching (Input terminal function 38 : FCHG enabled) Frequency priority selection parameter = Switching between the command specified with and can be made by entering a command from a terminal board. To do so, however, the frequency command forced switching function (input terminal function selection: 38) needs to be set beforehand to an input terminal board. If an OFF command is entered to the input terminal board: The command specified with will be selected. If an ON command is entered to the input terminal board: The command specified with will be selected. 2) Automatic switching by frequency command Frequency priority selection parameter = The switching between the command specified with and is done automatically according to the frequency command entered. If the frequency set with is above 1Hz: The command specified with will be selected. If the frequency set with is 1Hz or less: The command specified with will be selected. 1 0 2 6
Page 1 and 2:
Industrial Inverter For 3-phase ind
Page 3 and 4:
I General Operation Disassembly pr
Page 5 and 6:
4 E6581381 I Warning See item • E
Page 7 and 8:
I Disposal Mandatory 6 E6581381 Cau
Page 9 and 10:
⎯⎯ Contents ⎯⎯ I Safety pre
Page 11 and 12:
iii E6581381 12. Specifications....
Page 13 and 14:
1 1.2 Contents of the product Expla
Page 15 and 16:
1 Charge lamp Indicates that high v
Page 17 and 18:
1 VFFS1-2004 ∼ 2037PM VFFS1-4004
Page 19 and 20:
1 VFFS1-2220PM -4220, 4300, 4370, 4
Page 21 and 22:
1 22kW or more: Switch 3) Control c
Page 23 and 24:
1 A-12 E6581381 1.3.4 How to open t
Page 25 and 26:
1 Low loads and low inertia loads A
Page 27 and 28:
1 Power factor correction capacitor
Page 29 and 30:
1 (2) Affects of leakage current ac
Page 31 and 32:
1 A-20 E6581381 • Do not install
Page 33 and 34:
1 Calorific values of the inverter
Page 35 and 36:
2. Connection Disassembly prohibite
Page 37 and 38:
2.2.1 Standard connection diagram 1
Page 39 and 40:
2.3 Description of terminals 2.3.1
Page 41 and 42:
Terminal symbol Input/output Functi
Page 43 and 44:
B-9 E6581381 SINK (Negative) logic
Page 45 and 46:
3. Operations Prohibited Mandatory
Page 47 and 48:
3.1.1 How to start and stop Exampl
Page 49 and 50:
(2) Setting the frequency using the
Page 51 and 52:
Ex.2 (1) Wiring MCCB C-7 E6581381 R
Page 53 and 54:
4 4.1 Flow of status monitor mode F
Page 55 and 56:
4 4.2.1 How to set the basic parame
Page 57 and 58: 4 Example of parameter setting D-6
Page 59 and 60: 4 D-8 E6581381 [Parameter setting]
Page 61 and 62: 4 D-10 E6581381 4.2.6 Parameters th
Page 63 and 64: 5. Basic parameters Before you oper
Page 65 and 66: E-3 E6581381 [Parameter setting] Ti
Page 67 and 68: Coast stop (=) E-5 E6581381 Setting
Page 69 and 70: 5.3 Selection of operation mode Loc
Page 71 and 72: E-9 E6581381 Title Function Adjust
Page 73 and 74: Resolution All FM terminals have a
Page 75 and 76: 5.5 Standard default setting : Def
Page 77 and 78: 5.6 Forward/reverse run selection (
Page 79 and 80: E-17 E6581381 [Parameter setting] T
Page 81 and 82: E-19 E6581381 Warning: When setting
Page 83 and 84: Motor constant must be set E-21 E65
Page 85 and 86: Relationship between V/F control mo
Page 87 and 88: E-25 E6581381 [Parameter setting] T
Page 89 and 90: [Using a VF motor (motor for use wi
Page 91 and 92: E-29 E6581381 2) Preset-speed frequ
Page 93 and 94: 6. Extended parameters Extended par
Page 95 and 96: Output frequency [Hz] Designated fr
Page 97 and 98: Output frequency [Hz] + ― Ov
Page 99 and 100: F-7 E6581381 • Function Use the a
Page 101 and 102: 3) Sink (Negative) logic / Source (
Page 103 and 104: F-11 E6581381 (1) A signal is sent
Page 105 and 106: 6.3.6 Analog VIA / VIB detection :
Page 107: 6.4 Basic parameters 2 6.4.1 Switch
Page 111 and 112: F-19 E6581381 [Parameter setting] T
Page 113 and 114: RUN command Incrementing (UP) signa
Page 115 and 116: 6.5.4 Fine adjustment of frequency
Page 117 and 118: 6.7 DC braking 6.7.1 DC braking :
Page 119 and 120: PID command value LL F-27 E6581381
Page 121 and 122: 6.10 Bumpless operation LOC REM Key
Page 123 and 124: 100% 90% 80% 70% 60% Reduction of r
Page 125 and 126: 400V Class for IP20] Output current
Page 127 and 128: 2) Restarting motor during coasting
Page 129 and 130: Mandatory 6.12.3 Retry function :
Page 131 and 132: 6.12.4 Avoiding overvoltage trippin
Page 133 and 134: F-41 E6581381 [0: Supply voltage un
Page 135 and 136: F-43 E6581381 The droop control fu
Page 137 and 138: 2) Types of PID control interfaces
Page 139 and 140: (D-gain adjustment parameter) F-47
Page 141 and 142: [Selection 1: Setting vector contro
Page 143 and 144: F-51 E6581381 : Using this paramete
Page 145 and 146: 6.16 Acceleration/deceleration time
Page 147 and 148: F-55 E6581381 Title Function Adjust
Page 149 and 150: How to set parameters a) Operating
Page 151 and 152: F-59 E6581381 [Display during opera
Page 153 and 154: 6.17.5 Output phase failure detecti
Page 155 and 156: F-63 E6581381 Title Function Adjust
Page 157 and 158: 1) Output terminal function: 12 (OT
Page 159 and 160:
6.17.12 Undervoltage trip : Underv
Page 161 and 162:
F-69 E6581381 Output of part repla
Page 163 and 164:
6.18 Forced fire-speed control func
Page 165 and 166:
6.20 Operation panel parameter F-73
Page 167 and 168:
F-75 E6581381 6.20.3 Displaying the
Page 169 and 170:
An example of setting when is 80 a
Page 171 and 172:
Example of setting 2 F-79 E6581381
Page 173 and 174:
F-81 E6581381 [Parameter setting] T
Page 175 and 176:
The following are available as comm
Page 177 and 178:
6.21.2 Using the RS485 Setting the
Page 179 and 180:
6.22 Parameters for options : Para
Page 181 and 182:
7 (3) Input voltage setting 1 (0 to
Page 183 and 184:
7 Current signal Voltage signal G-4
Page 185 and 186:
7 G-6 E6581381 (3) Operation from a
Page 187 and 188:
8 Note 4 Note 5 Note 5 (Continued)
Page 189 and 190:
8 Note 10 Note 1 Note 2 Note 3 Note
Page 191 and 192:
8 Note 3 (Continued) Error code Fai
Page 193 and 194:
8 Note 6 Note 6 Note 6 Note 6 Note
Page 195 and 196:
9. Measures to satisfy the standard
Page 197 and 198:
I-3 E6581381 Three-phase 400V class
Page 199 and 200:
9.1.4 Measures to satisfy the low-v
Page 201 and 202:
Voltage class Three-phase 200V clas
Page 203 and 204:
10 J-2 E6581381 Note 4: For IEC, th
Page 205 and 206:
10 Magnetic contactor in the secon
Page 207 and 208:
11. Table of parameters and data 11
Page 209 and 210:
Title Communication No. Function Un
Page 211 and 212:
• Frequency parameters Title Comm
Page 213 and 214:
Title Communicatio n Function Unit
Page 215 and 216:
Page 217 and 218:
• Output parameters Title Communi
Page 219 and 220:
Page 221 and 222:
Table of input terminal functions 1
Page 223 and 224:
Table of output terminal functions
Page 225 and 226:
Table of output terminal functions
Page 227 and 228:
12 Principal control functions L-2
Page 229 and 230:
12 12.2 Outside dimensions and mass
Page 231 and 232:
12 Fig.E Fig.F Fig.G L-6 E6581381
Page 233 and 234:
13. Before making a service call -
Page 235 and 236:
M-3 E6581381 Error code (Continued)
Page 237 and 238:
M-5 E6581381 Note: When the ON/OFF
Page 239 and 240:
13.4 How to determine the causes of
Page 241 and 242:
14 Check points 1. Something unusu
Page 243 and 244:
14 N-4 E6581381 1) Cooling fan The
Page 245 and 246:
15. Warranty O-1 E6581381 Any part
Page 247:
TOSHIBA TOSHIBA INDUSTRIAL PRODUCTS
show all

VF-FS1 Industrial Inverter - Toshiba

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?