VF-FS1 Industrial Inverter - Toshiba

More documents

Recommendations

Info

A-19 E6581381 (2) CT and ammeter If a CT and ammeter are connected externally to detect inverter output current, the leak current's high frequency component may destroy the ammeter. If the wires are more than 50 meters long, it will be easy for the high frequency component to pass through the externally connected CT and be superimposed on and burn the ammeter with models having motors of low rated current (several A(ampere) or less), especially the 400V class low capacity (5.5kW or less) models, because the leak current will increase in proportion to the motor's rated current. Remedies: 1.Use a meter output terminal in the inverter control circuit. The load current can be output on the meter output terminal (FM). If the meter is connected, use an ammeter of 1mAdc full scale or a voltmeter of 7.5V(10V)-1mA full scale. 0-20mAdc (4-20mAdc) can be also output. ⇒ See section 5.4. 2.Use the monitor functions built into the inverter. Use the monitor functions on the panel built into the inverter to check current values. ⇒See section 8.1.1. 1.4.4 Installation Prohibited Mandatory Prohibited Mandatory Installation environment The VF-FS1 Inverter is an electronic control instrument. Take full consideration to installing it in the proper operating environment. Warning • Do not place any inflammable substances near the VF-FS1 Inverter. If an accident occurs in which flame is emitted, this could lead to fire. • Operate under the environmental conditions prescribed in the instruction manual. Operations under any other conditions may result in malfunction. Caution • Do not install the VF-FS1 Inverter in any location subject to large amounts of vibration. This could cause the unit to fall, resulting in bodily injury. • Check to make sure that the input power voltage is +10%, -15% of the rated power voltage written on the rating label (±10% when the load is 100% in continuous operation) If the input power voltage is not +10%, -15% of the rated power voltage (±10% when the load is 100% in continuous operation) this may result in fire. 1
1 A-20 E6581381 • Do not install in any location of high temperature, high humidity, moisture condensation and freezing and avoid locations where there is exposure to water and/or where there may be large amounts of dust, metallic fragments and oil mist. • Do not install in any location where corrosive gases or grinding fluids are present. • Operate in areas where ambient temperature ranges from -10°C to 60°C. When installing the inverter where the ambient temperature will rise above 40°C, remove the label (seal) from the top and operate it at a current lower than the rated one. 5cm 5cm 5cm Measurement position Measurement position Note: The inverter is a heat-emitting body. Make sure proper space and ventilation is provided when installing in the cabinet. When installing inside a cabinet, we recommend the top seal peeled off although 40°C or less. • Do not install in any location that is subject to large amounts of vibration. Note: If the VF-FS1 Inverter is installed in a location that is subject to vibration, anti-vibration measures are required. Please consult with Toshiba about these measures. • If the VF-FS1 Inverter is installed near any of the equipment listed below, provide measures to insure against errors in operation. Resistors Solenoids: Attach surge suppressor on coil. Brakes: Attach surge suppressor on coil. Magnetic contactors: Attach surge suppressor on coil. Fluorescent lights: Attach surge suppressor on coil. Resistors: Place far away from VF-FS1 Inverter.
Page 1 and 2: Industrial Inverter For 3-phase ind
Page 3 and 4: I General Operation Disassembly pr
Page 5 and 6: 4 E6581381 I Warning See item • E
Page 7 and 8: I Disposal Mandatory 6 E6581381 Cau
Page 9 and 10: ⎯⎯ Contents ⎯⎯ I Safety pre
Page 11 and 12: iii E6581381 12. Specifications....
Page 13 and 14: 1 1.2 Contents of the product Expla
Page 15 and 16: 1 Charge lamp Indicates that high v
Page 17 and 18: 1 VFFS1-2004 ∼ 2037PM VFFS1-4004
Page 19 and 20: 1 VFFS1-2220PM -4220, 4300, 4370, 4
Page 21 and 22: 1 22kW or more: Switch 3) Control c
Page 23 and 24: 1 A-12 E6581381 1.3.4 How to open t
Page 25 and 26: 1 Low loads and low inertia loads A
Page 27 and 28: 1 Power factor correction capacitor
Page 29: 1 (2) Affects of leakage current ac
Page 33 and 34: 1 Calorific values of the inverter
Page 35 and 36: 2. Connection Disassembly prohibite
Page 37 and 38: 2.2.1 Standard connection diagram 1
Page 39 and 40: 2.3 Description of terminals 2.3.1
Page 41 and 42: Terminal symbol Input/output Functi
Page 43 and 44: B-9 E6581381 SINK (Negative) logic
Page 45 and 46: 3. Operations Prohibited Mandatory
Page 47 and 48: 3.1.1 How to start and stop Exampl
Page 49 and 50: (2) Setting the frequency using the
Page 51 and 52: Ex.2 (1) Wiring MCCB C-7 E6581381 R
Page 53 and 54: 4 4.1 Flow of status monitor mode F
Page 55 and 56: 4 4.2.1 How to set the basic parame
Page 57 and 58: 4 Example of parameter setting D-6
Page 59 and 60: 4 D-8 E6581381 [Parameter setting]
Page 61 and 62: 4 D-10 E6581381 4.2.6 Parameters th
Page 63 and 64: 5. Basic parameters Before you oper
Page 65 and 66: E-3 E6581381 [Parameter setting] Ti
Page 67 and 68: Coast stop (=) E-5 E6581381 Setting
Page 69 and 70: 5.3 Selection of operation mode Loc
Page 71 and 72: E-9 E6581381 Title Function Adjust
Page 73 and 74: Resolution All FM terminals have a
Page 75 and 76: 5.5 Standard default setting : Def
Page 77 and 78: 5.6 Forward/reverse run selection (
Page 79 and 80: E-17 E6581381 [Parameter setting] T
Page 81 and 82:
E-19 E6581381 Warning: When setting
Page 83 and 84:
Motor constant must be set E-21 E65
Page 85 and 86:
Relationship between V/F control mo
Page 87 and 88:
E-25 E6581381 [Parameter setting] T
Page 89 and 90:
[Using a VF motor (motor for use wi
Page 91 and 92:
E-29 E6581381 2) Preset-speed frequ
Page 93 and 94:
6. Extended parameters Extended par
Page 95 and 96:
Output frequency [Hz] Designated fr
Page 97 and 98:
Output frequency [Hz] + ― Ov
Page 99 and 100:
F-7 E6581381 • Function Use the a
Page 101 and 102:
3) Sink (Negative) logic / Source (
Page 103 and 104:
F-11 E6581381 (1) A signal is sent
Page 105 and 106:
6.3.6 Analog VIA / VIB detection :
Page 107 and 108:
6.4 Basic parameters 2 6.4.1 Switch
Page 109 and 110:
F-17 E6581381 [Parameter setting] T
Page 111 and 112:
Page 113 and 114:
RUN command Incrementing (UP) signa
Page 115 and 116:
6.5.4 Fine adjustment of frequency
Page 117 and 118:
6.7 DC braking 6.7.1 DC braking :
Page 119 and 120:
PID command value LL F-27 E6581381
Page 121 and 122:
6.10 Bumpless operation LOC REM Key
Page 123 and 124:
100% 90% 80% 70% 60% Reduction of r
Page 125 and 126:
400V Class for IP20] Output current
Page 127 and 128:
2) Restarting motor during coasting
Page 129 and 130:
Mandatory 6.12.3 Retry function :
Page 131 and 132:
6.12.4 Avoiding overvoltage trippin
Page 133 and 134:
F-41 E6581381 [0: Supply voltage un
Page 135 and 136:
F-43 E6581381 The droop control fu
Page 137 and 138:
2) Types of PID control interfaces
Page 139 and 140:
(D-gain adjustment parameter) F-47
Page 141 and 142:
[Selection 1: Setting vector contro
Page 143 and 144:
F-51 E6581381 : Using this paramete
Page 145 and 146:
6.16 Acceleration/deceleration time
Page 147 and 148:
F-55 E6581381 Title Function Adjust
Page 149 and 150:
How to set parameters a) Operating
Page 151 and 152:
F-59 E6581381 [Display during opera
Page 153 and 154:
6.17.5 Output phase failure detecti
Page 155 and 156:
F-63 E6581381 Title Function Adjust
Page 157 and 158:
1) Output terminal function: 12 (OT
Page 159 and 160:
6.17.12 Undervoltage trip : Underv
Page 161 and 162:
F-69 E6581381 Output of part repla
Page 163 and 164:
6.18 Forced fire-speed control func
Page 165 and 166:
6.20 Operation panel parameter F-73
Page 167 and 168:
F-75 E6581381 6.20.3 Displaying the
Page 169 and 170:
An example of setting when is 80 a
Page 171 and 172:
Example of setting 2 F-79 E6581381
Page 173 and 174:
Page 175 and 176:
The following are available as comm
Page 177 and 178:
6.21.2 Using the RS485 Setting the
Page 179 and 180:
6.22 Parameters for options : Para
Page 181 and 182:
7 (3) Input voltage setting 1 (0 to
Page 183 and 184:
7 Current signal Voltage signal G-4
Page 185 and 186:
7 G-6 E6581381 (3) Operation from a
Page 187 and 188:
8 Note 4 Note 5 Note 5 (Continued)
Page 189 and 190:
8 Note 10 Note 1 Note 2 Note 3 Note
Page 191 and 192:
8 Note 3 (Continued) Error code Fai
Page 193 and 194:
8 Note 6 Note 6 Note 6 Note 6 Note
Page 195 and 196:
9. Measures to satisfy the standard
Page 197 and 198:
I-3 E6581381 Three-phase 400V class
Page 199 and 200:
9.1.4 Measures to satisfy the low-v
Page 201 and 202:
Voltage class Three-phase 200V clas
Page 203 and 204:
10 J-2 E6581381 Note 4: For IEC, th
Page 205 and 206:
10 Magnetic contactor in the secon
Page 207 and 208:
11. Table of parameters and data 11
Page 209 and 210:
Title Communication No. Function Un
Page 211 and 212:
• Frequency parameters Title Comm
Page 213 and 214:
Title Communicatio n Function Unit
Page 215 and 216:
Page 217 and 218:
• Output parameters Title Communi
Page 219 and 220:
Page 221 and 222:
Table of input terminal functions 1
Page 223 and 224:
Table of output terminal functions
Page 225 and 226:
Table of output terminal functions
Page 227 and 228:
12 Principal control functions L-2
Page 229 and 230:
12 12.2 Outside dimensions and mass
Page 231 and 232:
12 Fig.E Fig.F Fig.G L-6 E6581381
Page 233 and 234:
13. Before making a service call -
Page 235 and 236:
M-3 E6581381 Error code (Continued)
Page 237 and 238:
M-5 E6581381 Note: When the ON/OFF
Page 239 and 240:
13.4 How to determine the causes of
Page 241 and 242:
14 Check points 1. Something unusu
Page 243 and 244:
14 N-4 E6581381 1) Cooling fan The
Page 245 and 246:
15. Warranty O-1 E6581381 Any part
Page 247:
TOSHIBA TOSHIBA INDUSTRIAL PRODUCTS
show all

VF-FS1 Industrial Inverter - Toshiba

Create successful ePaper yourself

Delete template?

Save as template?