silo 3 - U.S. Department of Energy
silo 3 - U.S. Department of Energy
silo 3 - U.S. Department of Energy
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
. ...<br />
Access and Retrieval Strategy for the Silo 3 Project<br />
Document No. 40430-PL-0002, Rev. 1<br />
September 2003<br />
----?-15.Q-&--<br />
Vacuum wand - 4" diameter x 5' long aluminum tube sections (including a wand<br />
end effector section), with camlock fittings for addition <strong>of</strong> wand tube sections as<br />
pneumatic retrieval progresses deeper into the <strong>silo</strong>;<br />
Vacuum hose, to convey material from vacuum wand to PRS Collector, DCL-10-<br />
5002. The hose is corrugated (smooth interior surface), with a grounding wire<br />
embedded into the hose. Continuity checks can be conducted on the hose to test<br />
for wear areas caused by friction <strong>of</strong> the material;<br />
Motorized Hoist, secured on Silo 3 Enclosure ro<strong>of</strong> trusses above each man way,<br />
used to assist operator in lifting, lowering, and maneuvering the vacuum wand and<br />
hose;<br />
Hose cradle, with rollers, used in conjunction with hoist to support vacuum hose<br />
(preventing excessive hose bending) and to assist operator in maneuvering the<br />
vacuum wand and hose;<br />
Clamp-on "steering wheel", attached to vacuum wand, and used to assist the<br />
operator in maneuvering the vacuum wand;<br />
"Bullet" camera, taped to vacuum wand end effector, with monitor provided locally<br />
on <strong>silo</strong> dome and onwork platforms for operator viewing <strong>of</strong> vacuum wand retrieval<br />
performance inside the <strong>silo</strong>;<br />
Wooden platforms at five man ways (no platform at the center man way) to provide<br />
operators with a level-working surface.<br />
OTHER PRS EQUIPMENT<br />
\<br />
DCL-10-5002, Pneumatic Retrieval Collector, is a baghouse-type material collector<br />
used to separate the retrieved material from the associated air stream. Material and air<br />
is conveyed from the VWMS vacuum wands, via flexible vacuum hose, to the<br />
Pneumatic Retrieval Collector.<br />
FLT-10-5005, Cartridge Filter, provides additional removal <strong>of</strong> material from the air<br />
stream discharged from the Pneumatic Retrieval Collector.<br />
FLT-10-5004, HEPAAILPA Filter, provides additional removal <strong>of</strong> any material remaining<br />
in the air stream discharged from the Cartridge Filter.<br />
BLR-10-5006, Pneumatic Retrieval Blower, produces the pneumatic air stream and<br />
vacuum for the Pneumatic Retrieval System.<br />
FDR-10-5 1 04, Pneumatic Retrieval Collector Discharge Feeder, is a variable-speed<br />
screw feeder used to transfer material, at an operator-set rate, from the Pneumatic<br />
Retrieval Collector toward the project packaging system.<br />
ROF-10-5108, Primary Rotary Feeder, is used to provide an airlock between the high<br />
vacuum in the upstream Pneumatic Retrieval Collector and the low vacuum in the<br />
downstream Feed Conveyor and packaging system.<br />
ROF-10-5 1 10, Secondary Rotary Feeder, is used in series with the Primary Rotary<br />
Feeder to ensure an adequate airlock between the higher and lower vacuum systems.<br />
10<br />
000070<br />
e