Wireless G Router - Belkin

More documents

Recommendations

Info

section 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface Adding Another Network Segment Wirelessly Bridging an Access Point to your Wireless Router allows you to add another network segment in another area in the home or office without running wires. Connecting a network switch or hub to the Access Point’s RJ45 jack will allow a number of computers connected to the switch access to the rest of the network. 64
Using the Web-Based Advanced User Interface Setting Up a Bridge Between your Wireless Router and a Secondary Access Point Bridging your Belkin Router to a secondary Access Point requires that you access the Router’s Advanced Setup Utility and enter the MAC address of the Access Point in the appropriate area. There are also a few other requirements. PLEASE BE SURE TO FOLLOW THE STEPS BELOW, CAREFULLY. 1. Set your Access Point to the same channel as the Router. By default, the Router and Access Point channels are set to channel 11 at the factory. If you have never changed the channel, you don’t need to do anything (for more information on changing channels, see page 45 of this manual). 2. Find the Access Point’s MAC address on the bottom of the Access Point. There are two MAC addresses on the bottom label. You will need the MAC address named “WLAN MAC Address”. The MAC address starts with 0030BD and is followed by six other numbers or letters (i.e. 0030BD-XXXXXX). Write the MAC address below. Go to the next step. 65 0030BD-XXXXXX 3. Place your secondary Access Point within range of your Wireless Router and near the area where you want to extend the range or add the network segment. Typically, indoor range should be between 100 and 200 feet. 4. Connect power to your Access Point. Make sure the Access Point is on and proceed to the next step. 1 2 3 4 5 6 7 8 9 10 11 section
Page 1 and 2:
Share your broadband Internet acces
Page 3 and 4:
Introduction Thank you for purchasi
Page 5 and 6:
Introduction 2. Avoid Obstacles and
Page 7 and 8:
Introduction For more information r
Page 9 and 10:
Product Overview SPI Firewall Your
Page 11 and 12:
Knowing Your Router Package Content
Page 13 and 14:
Knowing Your Router the LED will li
Page 15 and 16: Knowing Your Router a. Resetting th
Page 17 and 18: Connecting and Configuring Your Rou
Page 25 and 26: Alternate Setup Method 1.5 Turn you
Page 27 and 28: Alternate Setup Method Logging out
Page 29 and 30: Alternate Setup Method 5. Help Butt
Page 31 and 32: Alternate Setup Method Setting your
Page 33 and 34: Alternate Setup Method Setting your
Page 35 and 36: Alternate Setup Method 6 My Subnet
Page 37 and 38: Alternate Setup Method 3. Password
Page 39 and 40: Alternate Setup Method Cloning your
Page 41 and 42: Using the Web-Based Advanced User I
Page 65: Using the Web-Based Advanced User I
Page 89 and 90: Manually Configuring Computer Netwo
Page 95 and 96: Recommended Web Browser Settings In
Page 97 and 98: Using your Router with AOL Broadban
Page 109 and 110: Troubleshooting Problem: Easy Insta
Page 111 and 112: Troubleshooting 2. Unplug the Cable
Page 113 and 114: Troubleshooting Problem: I can’t
Page 115 and 116: Troubleshooting Problem: My wireles
Page 117 and 118:
Troubleshooting Problem: I am havin
Page 119 and 120:
Troubleshooting 7. Type you WEP key
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Troubleshooting 5. Select “TKIP
Page 127 and 128:
Troubleshooting Technical Support Y
Page 129 and 130:
Information • Reorient or relocat
Page 131 and 132:
129 1 2 3 4 5 6 7 8 9 10 11
show all

Wireless G Router - Belkin

Create successful ePaper yourself

Delete template?

Save as template?