Jaguar XJ 1998 - JagRepair.com

CONTROL MODULE PIN OUT INFORMATION
BODY PROCESSOR MODULE
77 Pin Description
IGNITION SWTCHED GROUND
SEAT HEATER STATUS ,LHD = PASSENGER, RHD = DRIVER)
IGNITION SWITCHED GROUND
SEAT HEATER REQUEST (LHD = PASSENGER, RHD = DRIVERI
STARTER ENGAGE REQUEST
SEAT HEATER STATUS (LHD = DRIVER, RHD = PASSENGER)
BATTERY SVPPLY VOLTAGE
SEAT HEATER REQUEST (LHD = DRIVER, RHD = PASSENGER)
Active
GROUND
GROUND
GROUND
GROVND
GROUND
GROUND
B+
GROUND
iMOMENTARY,
(CRANKING)
(MOMENTARYI
Inactive
B+
B+
B+
B+
B+
Br
Bt
B+
COMPONENTS
Component Connector I Type / Color Location / Access
BODY PROCESSOR MODULE
FC15, ICWAYAMPEEECIGREY
BULKHEAD, BEHIND GLOVE BOX
SEATCVSHION HEATERS-DRIVER
%,7-D, S-WAY MULTILOCK 070,YELLOW
DRIVER SEAT
SEAT CUSHION HEATERS-PASSENGER
SM7-P, B-WAY MULTILOCK 070, YELLOW
PASSENGER SEAT
SEAT HEATER SWITCHES
CC,, 16.WAY FORD IDC S.U , BLACK
CENTER CONSOLE SWITCH PACK
(CENTER CONSOLE SWITCH PACK,
SEAT SQVAB HEATERS - DRIVER
SMS-D, 3.WAY MULTlLOCK 070, GREY DRIVER SEAT
SEAT SQUAB HEATERS PASSENGER
SMS-P, 3-WAY MULTILOCK 070, GREY PASSENGER SEAT
RELAYS
Relay Case Color Connector I Color Location / Access
SEAT HEATER RELAY-DRIVER
SEAT HEATER RELAY- PASSENGER
BROWN
BROWN
SM14-D,
SM,h-Pi
BROWN
BROWN
FRONT SEAT RELAYS, UNDER SEAT
FRONT SEAT RELAYS, UNDER SEAT
HARNESS-TO-HARNESS
CONNECTORS
Connector Type I Color Location / Access
CA23 ,&WAY MULTlLOCK 070, WHITE BELOW DRIVER SEAT
CA27 IO-WAY MULTlLOCK 070, WHITE BELOW PASSENGER SEAT
FC1 54.WAY THROUGH PANEL CONNECTOR, BLACK BELOW PASSENGER SIDE AIR VENT, GLOVE BOX ASSEMBLY
FC5 54.WAY THROUGH PANEL CONNECTOR, BLACK BELOW DRIVER SIDE AIR VENT, COIN TRAY
FC7 PO-WAY MULTlLOCK 070 /WHITE ABOVE DIMMER MODULE, COIN TRAY
-
GROUNDS
Ground Location / Type
CCBL
CA25L
CAZGL
EYELET iPAW - RH FRONT BULKHEAD STUD, CABIN SIDE
EYELET iPAlR) -PASSENGER SEAT GROUND STUD
EYELET (PAIR) DRIVER SEAT GROUND STUD
CONTROL MODULE PIN OUT INFORMATION (FOLD OUT PAGE)
+
The following symbols are used to represent values for Control Module Pin Out data:
I Input D Serial and encoded communications
B+ Battery voltage
KHz Frequency x 1000
0 output
C CAN (Network)
V Voltage (DC) MS Milliseconds
SG Signal Ground
S SCP Network Hz Frequency MV Millivolts
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation. THIS INFORMATION SHOULD BE USED FOR REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all
components connected and fitted. “Active” means a load is applied or a switch is ON; “Inactive” means a load is not applied or a switch is OFF.
REFER TO THE FRONT OF THE BOOK FOR ILLUSTRATIONS DETAILING THE LOCATION AND IDENTIFICATION OF COMPONENTS. RELAYS.
CONNECTORS, HARNESSES, GROUNDS, VEHICLE CONTROL MODULES AND CONTROL MODULE PINS.