download PDF - Gammill

More documents

Recommendations

Info

100 Getting Started with CreativeStudio * Total Width - is the width of all the repeats (measured from either the start/end points or measured from the outer edges of the patterns - see below). * Total Height - is the height of all the rows (measured from either the start/end points or measured from the outer edges of the patterns - see below). * Start End Controlled 125 (ON / OFF) means the total width/height is measured between the start / end points rather than the outer edges of the patterns. * Spacing (Horiz / Vert) is the distance between patterns. Positive numbers spread the patterns further apart and negative numbers bring them closer together. * Square Up Quilt Angle - is the number of degrees of rotation applied to the pattern group. This applies to patterns grouped together. * Select Between blocks - what to do between each pattern. - BobbinPullUp treats each pattern individually and will pause to allow the bobbin thread to be pulled up and trimmed. - Connect Start/End treats the patterns as a group, stitching them in a continuous path, joining the end of one pattern to the start of the next. Reference Point Location 50 Reference Point Selection is specific to the pattern, BEFORE the Square Up angle rotates the pattern. * Reference Point Position is how CS knows where to put the pattern image. It will appear in the preview area as a small blue circle with an arrow. * Offset from Point - is the distance (H and V) between the clicked reference point and what the pattern will use as a reference point.
Quilting the Quilt - Which CS Feature To use Phase 2 - Blocks Stitch Multiple Patterns using Repeat_Patterns 4. Click on the point on the quilt top that you will use as your reference point and the images are moved into the preview area. Reminder: Any of the process (Repeat Pattern Setup) details can be changed until you exit Setup Mode. Then, none of them is accessible, and all changes have to be done in Edit Mode which means the changes are made to the image in the preview area. Save Project Settings 60 often. Exit Setup mode by 1) closing the Repeat Pattern Setup dialog box, 2) changing to a different quilt group (tab) 3) opening another project. The individual patterns can now be edited as needed. Copyright © 2009 <strong>Gammill</strong>, Inc. | All Rights Reserved 101
Page 1 and 2:
Getting Started with CreativeStudio
Page 3 and 4:
Getting Started with CreativeStudio
Page 5 and 6:
Copyright © 2009 Gammill, Inc. | A
Page 7 and 8:
Foreword Foreword Gammill, Inc. is
Page 9 and 10:
1 Introduction Introduction Thank y
Page 11 and 12:
Introduction Technology Basics Equi
Page 13 and 14:
Introduction Technology Basics Term
Page 15 and 16:
Introduction Technology Basics Navi
Page 17 and 18:
1.2 Computer Skills Introduction Co
Page 19 and 20:
Introduction Computer Skills 'Explo
Page 21 and 22:
Page 23 and 24:
1.2.2 'Explore' Files Introduction
Page 25 and 26:
Page 27 and 28:
Part II
Page 29 and 30:
2.2.1 File Command Main Screen Layo
Page 31 and 32:
Main Screen Layout Command Bar Tool
Page 33 and 34:
Main Screen Layout Command Bar Help
Page 35 and 36:
2.3 Tool Bar Main Screen Layout Too
Page 37 and 38:
Main Screen Layout Tool Bar Edge To
Page 39 and 40:
2.4 Work Area Main Screen Layout Wo
Page 41 and 42:
2.4.2 Preview Area (CAD Screen) Mai
Page 43 and 44:
2.4.3.1 Project Details - Yellow Fr
Page 45 and 46:
Main Screen Layout Work Area Proper
Page 47 and 48:
Main Screen Layout Work Area Proper
Page 49 and 50: Main Screen Layout Work Area Proper
Page 55 and 56: Main Screen Layout Keypad Window re
Page 57 and 58: Part III
Page 59 and 60: 3.1.1 Origin Point Save your projec
Page 61 and 62: Planning the Quilting Quilt Project
Page 63 and 64: Planning the Quilting Quilt Groups
Page 65 and 66: 3.3.1 Single Block Patterns Plannin
Page 67 and 68: Planning the Quilting Quilt Pattern
Page 83 and 84: Part IV
Page 85 and 86: Quilting the Quilt - Which CS Featu
Page 91 and 92: 4.1.3 Stitch in the Ditch using Poi
Page 95 and 96: 4.2 Phase 2 - Blocks Quilting the Q
Page 99: Steps to follow: 1. Be sure the cor
Page 111 and 112: 4.3 Phase 3 - Borders Quilting the
Page 117 and 118: to the preview area. Quilting the Q
Page 129 and 130: pattern makes quilting the sashings
Page 133 and 134: 4.4 Phase 4 - Backgrounds Quilting
Page 143 and 144: Quick Reference E2E 4.4.3 E2E Alter
Page 151 and 152:
4.5 Record Mode Quilting the Quilt
Page 153 and 154:
4.6 Restart Quilting the Quilt - Wh
Page 155 and 156:
Quilting the Quilt - Which CS Featu
Page 157 and 158:
4.7 Utility Functions Quilting the
Page 159 and 160:
Quilting the Quilt - Which CS Featu
Page 161 and 162:
4.7.3 Oil Stitcher Routine Quilting
Page 163 and 164:
5 Quick Reference Sheets 5.1 QuickR
Page 165 and 166:
5.2 Quick Ref Regulated Quick Refer
Page 167 and 168:
5.3 Quick Ref P2P Line Quick Refere
Page 169 and 170:
5.4 Quick Ref P2P Pattern Quick Ref
Page 171 and 172:
5.5 Quick Ref Single Block Quick Re
Page 173 and 174:
5.6 Quick Ref Composite Blocks Quic
Page 175 and 176:
5.7 Quick Ref Text Blocks Feature:
Page 177 and 178:
Quick Reference Sheets Quick Ref Bo
Page 179 and 180:
5.10 Quick Ref Trim Outside Quick R
Page 181 and 182:
if you don’t like it, change it n
Page 183 and 184:
5.12 Quick Ref Record Quick Referen
Page 185 and 186:
Index - A - Active Screen 56 Add Pa
Page 187 and 188:
File Extension File Extension 17 Fi
Page 189 and 190:
P2P Icon 128 P2P patterns 128 P2P S
Page 191 and 192:
Restart with mouse 153, 155 Re-stit
Page 193 and 194:
Turning the quilt 111 Mark center p
Page 195:
Back Cover
show all

download PDF - Gammill

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?