download PDF - Gammill

More documents

Recommendations

Info

156 Getting Started with CreativeStudio 3A. Find the restart point using the sewing head - move the machine until the needle is just above the point where you want to continue stitching. Press “Use This Pt” on the keypad. CS moves to the closest stitch and waits for another response. If it looks good, Press Quilt and continue to sew. If not, try again by pressing “Use This Pt” until the right spot is found. 3B. Find the restart point using the computer screen - look at the image on the screen and find the crosshair mark - it is a long, skinny blue plus “+” sign. Zoom in and out using the roller on the mouse. Find the spot on the screen that corresponds to the restart point on the quilt, and click that spot with the mouse. The blue crosshair will move to this location on the screen and the stitcher will move to that location on the quilt. 4. When ready, press Quilt, and continue to sew. At the end of the quilting sequence, you will be prompted to pull up the bobbin thread and click OK. It doesn't matter how the bobbin thread is pulled up, secured or trimmed. Just be sure to click OK because it completes this process. Quick Reference Restart 184
4.7 Utility Functions Quilting the Quilt - Which CS Feature To use Utility Functions Utility Functions are used in many different techniques. They are very important, but not used on a regular basis. 4.7.1 Set Defaults There are many mechanical, electrical, and numeric default settings that are required to run CS. The defaults are the initial values that are set every time CS starts up. Many of these values can be changed as needed during the quilting session. Others are considered Restricted Areas and should not be modified without the help and guidance of the Statler Stitcher Technical Support staff. The user controlled values are described in the following text. To find the defaults you can change: * Click Tools, * Click Technical Support, * Click Controller Definition * User Settable Tab contains your default values. Copyright © 2009 <strong>Gammill</strong>, Inc. | All Rights Reserved 157
Page 1 and 2:
Getting Started with CreativeStudio
Page 3 and 4:
Getting Started with CreativeStudio
Page 5 and 6:
Copyright © 2009 Gammill, Inc. | A
Page 7 and 8:
Foreword Foreword Gammill, Inc. is
Page 9 and 10:
1 Introduction Introduction Thank y
Page 11 and 12:
Introduction Technology Basics Equi
Page 13 and 14:
Introduction Technology Basics Term
Page 15 and 16:
Introduction Technology Basics Navi
Page 17 and 18:
1.2 Computer Skills Introduction Co
Page 19 and 20:
Introduction Computer Skills 'Explo
Page 21 and 22:
Page 23 and 24:
1.2.2 'Explore' Files Introduction
Page 25 and 26:
Page 27 and 28:
Part II
Page 29 and 30:
2.2.1 File Command Main Screen Layo
Page 31 and 32:
Main Screen Layout Command Bar Tool
Page 33 and 34:
Main Screen Layout Command Bar Help
Page 35 and 36:
2.3 Tool Bar Main Screen Layout Too
Page 37 and 38:
Main Screen Layout Tool Bar Edge To
Page 39 and 40:
2.4 Work Area Main Screen Layout Wo
Page 41 and 42:
2.4.2 Preview Area (CAD Screen) Mai
Page 43 and 44:
2.4.3.1 Project Details - Yellow Fr
Page 45 and 46:
Main Screen Layout Work Area Proper
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Main Screen Layout Keypad Window re
Page 57 and 58:
Part III
Page 59 and 60:
3.1.1 Origin Point Save your projec
Page 61 and 62:
Planning the Quilting Quilt Project
Page 63 and 64:
Planning the Quilting Quilt Groups
Page 65 and 66:
3.3.1 Single Block Patterns Plannin
Page 67 and 68:
Planning the Quilting Quilt Pattern
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Part IV
Page 85 and 86:
Quilting the Quilt - Which CS Featu
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
4.1.3 Stitch in the Ditch using Poi
Page 93 and 94:
Page 95 and 96:
4.2 Phase 2 - Blocks Quilting the Q
Page 97 and 98:
Page 99 and 100:
Steps to follow: 1. Be sure the cor
Page 101 and 102:
Page 103 and 104:
Page 105 and 106: Quilting the Quilt - Which CS Featu
Page 111 and 112: 4.3 Phase 3 - Borders Quilting the
Page 117 and 118: to the preview area. Quilting the Q
Page 129 and 130: pattern makes quilting the sashings
Page 133 and 134: 4.4 Phase 4 - Backgrounds Quilting
Page 143 and 144: Quick Reference E2E 4.4.3 E2E Alter
Page 151 and 152: 4.5 Record Mode Quilting the Quilt
Page 153 and 154: 4.6 Restart Quilting the Quilt - Wh
Page 155: Quilting the Quilt - Which CS Featu
Page 161 and 162: 4.7.3 Oil Stitcher Routine Quilting
Page 163 and 164: 5 Quick Reference Sheets 5.1 QuickR
Page 165 and 166: 5.2 Quick Ref Regulated Quick Refer
Page 167 and 168: 5.3 Quick Ref P2P Line Quick Refere
Page 169 and 170: 5.4 Quick Ref P2P Pattern Quick Ref
Page 171 and 172: 5.5 Quick Ref Single Block Quick Re
Page 173 and 174: 5.6 Quick Ref Composite Blocks Quic
Page 175 and 176: 5.7 Quick Ref Text Blocks Feature:
Page 177 and 178: Quick Reference Sheets Quick Ref Bo
Page 179 and 180: 5.10 Quick Ref Trim Outside Quick R
Page 181 and 182: if you don’t like it, change it n
Page 183 and 184: 5.12 Quick Ref Record Quick Referen
Page 185 and 186: Index - A - Active Screen 56 Add Pa
Page 187 and 188: File Extension File Extension 17 Fi
Page 189 and 190: P2P Icon 128 P2P patterns 128 P2P S
Page 191 and 192: Restart with mouse 153, 155 Re-stit
Page 193 and 194: Turning the quilt 111 Mark center p
Page 195: Back Cover
show all

download PDF - Gammill

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?