Pipelaying Tender-VOL I - WorleyParsons.com

PRICE SCHEDULE (INDIAN BIDDERS)Schedule of Quantities for 18” dia Rewari - Kanpur Cross Country Pipeline ( Part II)RCC - Providing & laying in position controlled grade reinforced cement concrete conforming to is:456-2000,with design mix of required gradeat all locations and levels using 20mm and down size graded aggregates in all types of works [including leaving pockets, placing of conduits,making openings, pockets placing inserts/ sleeves in columns/ beams/ slabs etc.] machine mixing, using admixtures are required, lifting,placing, machine vibrating, tamping, curing etc. as specified, complete as per drawings & / or as directed by WP / HPCL engineer incharge.ready mix concrete may be used by contractor with concrete having required quality at no extra cost.200 RCC for m30 gradeNote: (1) The rate also includes cost of providing offsets, cutouts, formwork, construction joints, making holes in or cutting formwork for taking Cu. M 31out dowel bars, hacking the exposed surfaces to receive plaster as necessary.(2) rate of providing and fixingreinforcement steel and any other embedded steel items shall be measured and paid seperately.Same as above, but for M30 grade concrete for below ground works for footings/foundations, plinth beams, raft slabs, pedestals, trenches,manhole pit, culverts, drains, sumps, pits equipment foundations, encasing of pipes etc at depth below and upto plinth level.201RCC for m20 gradeProviding, supplying & casting in place RCC M20 grade slab/paving with all required machinaries/accessories by using vacuum dewateringmethod (tremix flooring or equivalent) inclusive of shuttering,all construction, isolation, expansion joints & tests,curing, etc complete asdirected by WP/HPCL engineer in charge. The reinforcement shall be paid separately.Cu. M 130REINFORCEMENT-Providing, laying & fixing in position reinforcement as per dwg. locations & levels including bar bending schedules &obtaining their approval, cutting, bending & binding with 16g MS annealed binding wire incl. placing proper concrete cover blocks, chair202 Reinforcement HYSD IS1786MT 13supports etc complete as specified and directed by wp/hpcl engineer in charge.HYSD conforming to IS:1786 of Grade Fe415Anchor bolts and relevant accessories like plates, nuts, pipesleeves etc. bolts shall be turned from M.S. rounds conforming to IS 2062 and IS432 grade 1. Nuts and washers shall conform to IS 1363 and IS 3138. Threading shall be coarse conforming to IS 1367 and IS 4218, sleeves203 Anchor boltingMT 1shall be M.S. tubes – medium to IS 1239.Embedded insert plates, insert/corner angles/channels, pipesleeves alongwith lugs/holdfast including painting as per painting specifications for204 Enbedded insert platessteel structures. Plate/angle/channels shall be conforming to IS 2062. Lugs shall be M.S. rounds conforming to IS 2062 and IS 432 Grade 1. MT 1.5205Prv & Lay Non srink groutProviding and laying non-shrink premix type grout (Fosroc or equivalent make) having minimum compressive strength of 40N/mm2 includingproviding necessary formwork as required.Cu. M 3STRUCTURAL STEEL AND ALLIED WORKS206 STRUCTURAL STEEL & ALLIEDProviding, fabricating, welding and/or bolting, as required, erecting and fixing in position all types of structural steel works (including paintingas per specifications : MH2145-C000-CI-SPC-0005) viz. columns,beams, monorails, rafters, trusses, purlins,frame for louvres, bracing,ladders and cage ladders, sag rods (except cheqd. plates, grating & pipe railing only) made up of rolled & built up sections with moment orshear connections, shop/site fabricated including all accessories viz. nuts, bolts, cleats, gussets, suspenders etc as per specification completeas directed by WP/ HPCL Engineer incharge. The rate to include for welding weights, site connection, nut & bolts and same will not bemeasured for payment.(painting & sand blasting shall be included in this item.) The rate shall include for preparing & providing detailedfabrication drawings based on design drawings & getting the same approved from the WP / HPCL Engineer incharge.MT 10207Electrical System for SV's208Electrical System for IPS209Laying 11KV Power supply211Laying 11KV beyond 3kms212 TCP213 PCPElectrical SystemContractor to quote for the lump sum amount for the Residual design , supply, Installation, testing, commissioning of complete ElectricalSystem including Transportation to site, Loading, unloading, Storage, packing, unpacking etc. at site of Electrical Equipments & accessioriesall complete as per detailed scope of work ( MH2145-C000-EL-REQ-0009 ), specifications, design basis, data sheets, SLDs, other provisionsof contract document and directions of Engineer-In-ChargeElectrical system for SV-07,08,09,10,11Electrical system for IP Station at Saiyyadpur PranLaying of 11KV power supply line from the point of supply identified / approved by State Electricity Board / Owner to the SV/IP station ( OHline upto a maximum distance of 3Kms) including supply & installation of two pole structures, Transformer, CT/PT etc.as per the approveddrawings, schematics including supply of all material from approved vendors, installation, terminations at all ends including switchgear end,testing and Commissioning as per the scope of work, specifications and provisions of the contract document, instructions of Engineer-in-Charge and terms & conditions of SEB approval.All the works as above for any distance over & above 3Kms all complete as per the scope of work, specifications and provisions of the contractdocument, instructions of Engineer-in-Charge and terms & conditions of SEB approval.Cathodic Protection SystemTemporary Cathodic Protection(T-C-P) system ( scope as per Annexure 1 and 2 of Scope of Work -Electrical) for Ch 227.706 to EndReceiving Station at KanpurPermanent Cathodic Protection(P-C-P) system ( scope as per Annexure 1 and 2 of Scope of Work - Electrical) for Ch 227.706 to EndReceiving Station at Kanpur, including identification & provision of anode beds including acquisition of land (in the name of HPCL) for AnodeBeds (each approx. 10 m X 10 m) including land development site / area grading as required all complete as per the Scope of Work,Specifications, Provisions of Contract document and directions of Engineer-In-ChargeNote: Contractor to decide the locations and the TCP/PCP requirements for chainage 227.706 to End Receiving Station at KanpurLUMP5SUMLUMP1SUMLUMP6SUMMtr 10000LUMP1SUMLUMP1SUM214 Prssure gauges Bourdon215 Pressue indicating Trans216 Temp Element & trans217 Temp Element & transInstrumentation SystemPRESSURE GAUGE -Type : BOURDON TUBEInstallation & Calibration of Line mounted or Remote mounted Pressure Gauge with Pulsation Dampener / Syphon / Overrange Protector(Wherever required) inclusive of mounting of instrument, Installation of tubing materials such as valves fittings, pipes, tubes, compressionfittings as per specification, erection of support, mounting on support, (if support required), laying of capillary on supports and installation ofmanifolds/ impulse lines with supports and tubings with SS compression fittings as per specification No. MH2145-C000-IC-SPC-006 /MH2145-C000-IC-SPC-0017 including the cost of all labour, materials, equipment etc. as per specifications, drawings, codes and standardsand as directed by the Engineer-in-charge.PRESSURE INDICATING TRANSMITTERInstallation & Calibration of Pressure Transmitters including mounting on Yoke / Surface, piping & tubing materials such as valves, fittings,pipes, tubes, compression fittings, supports for capillary (if any) , erection of supports for impulse lines whenever required, installation ofmanifolds/ impulse lines with supports an tubings with SS compression fittings as per specification No. MH2145-C000-IC-SPC-006 /MH2145-C000-IC-SPC-0017 including the cost of all labour, materials, equipment etc. as per specifications, drawings, codes and standardsand as directed by the Engineer-in-charge.TEMPERATURE ELEMENT WITH TEMPERATURE TRANSMITTER-Type :Skin Temperature measurementInstallation & Calibration of RTD element along with Temperature Transmitter remote mounted. Installation of transmitter including mountingon yoke, fabrication and erection of supports with clamps and laying of extension/RTD cable, Yoke and Calibration as per specification No.MH2145-C000-IC-SPC-006 / MH2145-C000-IC-SPC-0017 including the cost of all labour, materials, equipment etc. as per specifications,drawings, codes and standards and as directed by the Engineer-in-charge.TEMPERATURE ELEMENT WITH TEMPERATURE TRANSMITTERInstallation & Calibration of RTD element with thermowell, along with Temperature Transmitter remote mounted. Installation of transmitterincluding mounting on yoke, fabrication and erection of supports with clamps and laying of extension/RTD cable, Yoke and Calibration as perspecification No. MH2145-C000-IC-SPC-006 / MH2145-C000-IC-SPC-0017 including the cost of all labour, materials, equipment etc. as perspecifications, drawings, codes and standards and as directed by the Engineer-in-charge.nos. 16nos. 15nos. 13nos. 2218 Inst Thermal relief valve219 Inst&Calb wall heat detect220 Inst&Calb smokedetect opt221 Inst&Calb smokedetect ion222 Inst&Calb Hydrogen detect223 Inst&Calb MCP224 Inst&Calb audio alarm225 Inst&Calb audio alarm226 FIRE ALARM PANEL, RTU227 Supply FAS equipment228 Extra Depth bet. 2 to 5 mtrNOTE:1NOTE:2NOTE:3THERMAL RELIEF VALVEInstallation of TSV on piping / vessel with or without isolation valves as per requirement ,Installation of valve including fabrication and erectionof supports with clamps and Calibration. including the cost of all labour, materials, equipment etc. as per datasheet no, (Doc no. MH2145-C000-IC-DAS-0002) drawings, codes and standards and as directed by the Engineer-in-charge.Installation & Calibration of wall mounted heat detector-Type: Rate of rise Heat, 24V DC, 4-20mA O/p, Safe Area, IP 42 (minimum)As per Specification no. MH2145-C000-00-IC-SPC-0009.Installation & Calibration of wall mounted smoke detector-Type: Optical Type Smoke, 24V DC, 4-20mA O/p, Safe Area, IP42 (minimum).As per Specification no. MH2145-C000-00-IC-SPC-0009.Installation & Calibration of wall mounted smoke detector-Type: lonisation Type Smoke, 24V DC, 4-20mA O/p, Safe Area, IP42 (minimum).As per Specification no. MH2145-C000-00-IC-SPC-0009.Installation & Calibration of Hydrogen Gas Detector for Battery Room.As per Specification no. MH2145-C000-00-IC-SPC-0009.Installation & Calibration of Manual Alarm Call Point double action "break glass" unit.As per Specification no. MH2145-C000-00-IC-SPC-0009.Installation & Calibration of Visual Alarm 24VDC,IP66,Explosion proof ,ZONE-1,ISAs per Specification no. MH2145-C000-00-IC-SPC-0009.Installation & Calibration of Audio Alarm 4VDC,IP66,Explosion proof ,ZONE-1.As per Specification no. MH2145-C000-00-IC-SPC-0009.FIRE ALARM PANEL, RTU, TELECOMMUNICATION SYSTEM: Erection of Units suppiled by vendors of Telecom, SCADA packages,including supply & laying of cables laying as per the approved cable layout between indoor units and from field instruments to indoor unitsincluding cable terminations as required, all necessary assistance to package vendors for Testing & Commissioning all complete as per thescope of work, specifications and directions of Engineeer-in-ChargeSUPPLY OF FIRE FIGHTING & SAFETY EQUIPMENTRESIDUAL DESIGN, ENGINEERING, MATERIALS, FABRICATION, ASSEMBLY, INSPECTION, TESTING, PAINTING,DOCUMENTATION, SUPPLY AND SHIPMENT OF ALL ITEMS LISTED UNDER SCOPE OF WORK DOCUMENT NO ."MH2145-C000-SR-SOW-0001", Specifications, Data Sheets, provisions of the contract document and directions of Engineer-In-Charge. The item shall alsoinclude placement of all the equipment as per approved equipment arrangement drawing / layoutAdditional rate over pipeline laying described under line no. 110,111,112,113 & 114 with extra clearcover of 2m to 5m beyond that defined inthe alignment sheet for single approved stretch beyond 150m pre-approved by site-in-charge based on site condition.All fire extinguishers shall conform to respective IS/UL or Equivalent codes, viz. 10 Kg DCP Type (applicable IS:/UL Standard), 4.5/6,8 KgCO2 Type (IS:2878/UL 154) & 25/50/75 Kg DCP Type (IS:10658/UL 299) and bear ISI/UL markSafety Equipment / CO2 flooding system shall meet OISD / NFPA requirement and shall bear relevant/required IS/UL markSafety Signages shall be supplied as lot item based on site requirements.nos. 8nos. 18nos. 36nos. 24nos. 6nos. 24nos. 24nos. 30nos. 6NOS. 6Meters 3000Page 7 of 9