Manual - AEQ International

More documents

Recommendations

Info

Digital input 4 Digital input 3 Digital input 2 Digital input 1Jumpers J42, J47, J48, Jumpers J25, J26, J30, Jumpers J41, J43, J44, Jumpers J23, J24, J27,J50 and J55 J32 and J37 J46 and J51 J29 and J33Position 1-2: AES/EBUPosition 2-3: S/PDIF2.2.3.3. Digital outputs.AEQ CAPITOL includes 4 stereo balanced digital outputs available through a female DB15connector identified as “AES OUT 1-4” configurable one by one as AES/EBU (by default) orS/PDIF by configuring the corresponding jumpers.Digital Outputs (SUB-D female, 15 pins):Pin Signal Pin Signal1 OUT1+ 9 OUT1-2 GND 10 GND3 OUT2+ 11 OUT2-4 GND 12 GND5 OUT3+ 13 OUT3-6 GND 14 GND7 OUT4+ 15 OUT4-8 GNDIn order to make installation process easier, AEQ offers specific pre-fabricated cable kits forAEQ CAPITOL audio input/output, both analog and digital, as well as studio headphones: FRCAB INP, consisting in a male DB15 connector soldered to 4 balanced and shielded 6 meterslong paired cables with no connectors at the other end, for 4 inputs or outputs. For moreinformation please check chapter 2.2.6 of this manual.AEQ can upon request provide fully finished cables and in special lengths. For more informationplease refer to AEQ sales department or authorised distributors.AEQ CAPITOLUltra-compact digital audio mixer28
- Programming digital outputs as S/PDIF.In order to provide outputs to S/PDIF equipments, the programming proceduredescribed below adapts the levels and unbalances the signals by joining OUT1- ,OUT2-, OUT3-, and OUT4- to their corresponding GND, so the signal is taken fromeach OUT+ to OUT– (or GND).Start by following the steps detailed at chapter 2.2.3.1 (it’s VERY IMPORTANT to turnfirst the equipment off and disconnect the power supply cable). Then, at the “DIGITALINPUTS AND OUTPUTS PROGRAMMING ZONE”, you can change the outputs one byone from AES/EBU to S/PDIF by moving the 4 jumpers associated to each output fromposition 1-2 (up) to position 2-3 (down), as shown in the following image:Digital output 4 Digital output 3 Digital output 2 Digital output 1Jumpers J49, J56, Jumpers J31, J38, Jumpers J45, J52, Jumpers J28, J34,J57 and J58 J39 and J40 J53 and J54 J35 and J36Position 1-2: AES/EBUPosition 2-3: S/PDIF2.2.3.4. Analog inputs.AEQ CAPITOL includes 12 mono line-level inputs, electronically balanced, available through 3female DB15 connectors identified as “ANALOG IN 1-4”, “ANALOG IN 5-8” and “ANALOG IN9-12”.Analog Inputs (SUB-D female, 15 pins):AEQ CAPITOLUltra-compact digital audio mixer29
Page 5: Its Ethernet port enables the local
Page 8: In addition to the signals on chann
Page 12 and 13: VU metersPROGRAMMABLEKEYSMAINSCREEN
Page 14 and 15: At most, the last line will have fo
Page 16 and 17: • The three rotary encoders, from
Page 18 and 19: 2.1.3. Wrist- rest and side trims.A
Page 20 and 21: 2.2.1. Power supply.The power suppl
Page 22 and 23: • Maximum power: 100mW at 40 ° C
Page 24 and 25: 2.2.2.3. Control and studio monitor
Page 26 and 27: - Opening the unit.It’s VERY IMPO
Page 30 and 31: “ANALOG IN 1-4” connectorPin Si
Page 32 and 33: MIC/LINE input 4 MIC/LINE input 3 M
Page 34 and 35: 2.2.4.2. CA33 telephone hybrid opti
Page 36 and 37: 3. DESCRIPTION OF THE INTERNAL MENU
Page 38 and 39: • “CHRONO”: enables you to co
Page 41 and 42: • “BACK”: pressing this key a
Page 43 and 44: 3.4.3. “SELECT“ menu.This menu
Page 45 and 46: The “Compressor / Limiter” func
Page 47 and 48: In addition, the threshold must be
Page 49 and 50: • In mic/line channels, indicatio
Page 51 and 52: • Indication of audio signal type
Page 53 and 54: Only the users defined as administr
Page 55 and 56: There are two distinct areas in thi
Page 57 and 58: The “Unlock” button allows you
Page 59 and 60: The lower part of the “User Confi
Page 61 and 62: 4.2.1. “Board Configuration” su
Page 63 and 64: o“TH02”: GPI to accept the part
Page 65 and 66: The mixer bus configuration table h
Page 67 and 68: 4.2.3.1. Advanced configuration of
Page 69 and 70: • “Mono”: allows you to defin
Page 71 and 72: 4.2.4.1. “Studio Room Section“.
Page 73 and 74: 4.3. “Programmable Configuration
Page 75 and 76: 4.3.2. “Programmable Keys” subm
Page 77 and 78: • “Latch Mode”: allows you to
Page 79 and 80:
4.3.2.4. Configuration of “Codec
Page 81 and 82:
• “On Air GPI”: selects and c
Page 83 and 84:
The lower part of the “Programmab
Page 85 and 86:
The three buttons at the bottom of
Page 87 and 88:
Allows you to scroll to the top of
Page 89 and 90:
• “ATTACK TIME”: this is the
Page 91 and 92:
4.3.4.4. Advanced configuration of
Page 93 and 94:
The available options in the snapsh
Page 95 and 96:
From left to right and from top to
Page 97 and 98:
4.4. “Firmware Upgrade” menu.Th
Page 99 and 100:
In case you select an AFU file that
Page 101 and 102:
5. A.E.Q. GUARANTEE.AEQ warrants th
show all

Manual - AEQ International

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?