Manual - AEQ International

More documents

Recommendations

Info

Selecting any of the modules, the associated firmware information will be shown.The procedure to upgrade a module firmware is as follows:1. Place the pointer on the module to be upgraded, press the right mouse button and thenthe “Upgrade” option that appears.2. In the new window that appears, press the button and select the “AFU” upgradingfile (AEQ Firmware Upgrade) that contains the new version you want to load.AEQ CAPITOLUltra-compact digital audio mixer98
In case you select an AFU file that does not correspond to the selected module, an errormessage will be displayed:3. Then press “Send” button to start the upgrading process.4. From this point on, the application changes automatically to “Upgrade View” screen inorder to show you the upgrading progress. See section 4.4.2 of this manual.IMPORTANT NOTE: You should not act on the system and you must never turn off theequipment during the upgrading process, since this action may deprogram the module that youare trying to upgrade. The firmware upgrade right order is: MSC module and BASE PBA(FPGA, DSP Process, DSP Router and CPU). The CA33 telephone hybrid module will appearas an upgradable module inside the base board (as well as an independent module) and will beupgraded from here.4.4.2. “Upgrade View” submenu.“Upgrade View” submenu is accessed, from the drop-down menu “Firmware Upgrade”, byclicking on the icon (although the application will change automatically to this submenu when anfirmware upgrading is in process):“Upgrade View” submenu allows you to check in real time the upgrading progress.AEQ CAPITOLUltra-compact digital audio mixer99
Page 5:
Its Ethernet port enables the local
Page 8:
In addition to the signals on chann
Page 12 and 13:
VU metersPROGRAMMABLEKEYSMAINSCREEN
Page 14 and 15:
At most, the last line will have fo
Page 16 and 17:
• The three rotary encoders, from
Page 18 and 19:
2.1.3. Wrist- rest and side trims.A
Page 20 and 21:
2.2.1. Power supply.The power suppl
Page 22 and 23:
• Maximum power: 100mW at 40 ° C
Page 24 and 25:
2.2.2.3. Control and studio monitor
Page 26 and 27:
- Opening the unit.It’s VERY IMPO
Page 28 and 29:
Digital input 4 Digital input 3 Dig
Page 30 and 31:
“ANALOG IN 1-4” connectorPin Si
Page 32 and 33:
MIC/LINE input 4 MIC/LINE input 3 M
Page 34 and 35:
2.2.4.2. CA33 telephone hybrid opti
Page 36 and 37:
3. DESCRIPTION OF THE INTERNAL MENU
Page 38 and 39:
• “CHRONO”: enables you to co
Page 41 and 42:
• “BACK”: pressing this key a
Page 43 and 44:
3.4.3. “SELECT“ menu.This menu
Page 45 and 46:
The “Compressor / Limiter” func
Page 47 and 48: In addition, the threshold must be
Page 49 and 50: • In mic/line channels, indicatio
Page 51 and 52: • Indication of audio signal type
Page 53 and 54: Only the users defined as administr
Page 55 and 56: There are two distinct areas in thi
Page 57 and 58: The “Unlock” button allows you
Page 59 and 60: The lower part of the “User Confi
Page 61 and 62: 4.2.1. “Board Configuration” su
Page 63 and 64: o“TH02”: GPI to accept the part
Page 65 and 66: The mixer bus configuration table h
Page 67 and 68: 4.2.3.1. Advanced configuration of
Page 69 and 70: • “Mono”: allows you to defin
Page 71 and 72: 4.2.4.1. “Studio Room Section“.
Page 73 and 74: 4.3. “Programmable Configuration
Page 75 and 76: 4.3.2. “Programmable Keys” subm
Page 77 and 78: • “Latch Mode”: allows you to
Page 79 and 80: 4.3.2.4. Configuration of “Codec
Page 81 and 82: • “On Air GPI”: selects and c
Page 83 and 84: The lower part of the “Programmab
Page 85 and 86: The three buttons at the bottom of
Page 87 and 88: Allows you to scroll to the top of
Page 89 and 90: • “ATTACK TIME”: this is the
Page 91 and 92: 4.3.4.4. Advanced configuration of
Page 93 and 94: The available options in the snapsh
Page 95 and 96: From left to right and from top to
Page 97: 4.4. “Firmware Upgrade” menu.Th
Page 101 and 102: 5. A.E.Q. GUARANTEE.AEQ warrants th
show all

Manual - AEQ International

Create successful ePaper yourself

Delete template?

Save as template?