Manual - AEQ International

More documents

Recommendations

Info

For TH02 hybrid, the available configuration options are:• “Ring”: allows you to select the GPI where the incoming call signal provided by thehybrid is wired. The key starts to blink when there is an incoming call. This function canbe combined in the same key with any of the following three functions.NOTE: the working mode of the selected GPI must be previously configured as “TH02”(see section 4.2.1.1 of this manual).• “Extended”: enables the option of frequency extender for the TH02 telephone hybridand select the GPO used to send the remote control signal to the hybrid. The key turnson when activated.• “Wait GPO”: selects and configures the physical GPO output associated to “WAIT”function. The key turns on when activated and puts the call on hold (WAIT mode).• “On Air GPO”: selects and configures the physical GPO output associated to “ON AIR”function. The key turns on when activated and puts the call on the air (ON AIR mode).• “Line”: for dual line hybrids such as TH02, this identifies the integrated line 1 and line 2,to assign the different GPIs and GPOs for remote control• “OK”: allows you to accept the created or edited configuration.• “Cancel”: allows you to reject the created or edited configuration. No change you mayhave made is saved.IMPORTANT NOTE: “Extended”, “Wait GPO” and “OnAir GPO” functions are exclusivebetween them (a programmable key can have only one of the three options associated),although any of them can be combined in the same key with “Ring” function.For Eagle audio-codec, the available configuration options are:• “Ring”: allows you to select the GPI where the incoming call signal provided by thecodec is wired. The key starts to blink when there is an incoming call. This function canbe combined in the same key with any of the following four functions.• “Wait GPI”: selects and configures the physical GPI input associated to “WAIT”function. The key turns on when WAIT mode (call on hold) is activated manually in theaudio-codec.• “Wait GPO”: selects and configures the physical GPO output associated to “WAIT”function. The key turns on when activated and puts the call on hold (WAIT mode).AEQ CAPITOLUltra-compact digital audio mixer80
• “On Air GPI”: selects and configures the physical GPI input associated to “ON AIR”function. The key turns on when ON AIR mode (call on the air) is activated manually inthe audio-codec.• “On Air GPO”: selects and configures the physical GPO output associated to “ON AIR”function. The key turns on when activated and puts the call on the air (ON AIR mode).• “Line”: for dual line codecs such as Eagle and Phoenix Studio, this identifies theintegrated line 1 and line 2, to assign the different GPIs and GPOs for remote control.• “OK”: allows you to accept the created or edited configuration.• “Cancel”: allows you to reject the created or edited configuration. No change you mayhave made is saved.IMPORTANT NOTE: The pairs of functions “Wait GPI”-“Wait GPO” and “On Air GPI”-“On AirGPO” are exclusive between them (a programmable key can have only one of the two pairsassociated).For Codecs it is usual to program at least two programmable keys per channel:one to share “Ring”, “Wait GPI” and “Wait GPO” functions and another one toshare “On Air GPI” and “On Air GPO” functions. The following screens show anexample of programmable keys configuration for remote control of an AEQEAGLE audio-codec.123AEQ CAPITOLUltra-compact digital audio mixer81
Page 5:
Its Ethernet port enables the local
Page 8:
In addition to the signals on chann
Page 12 and 13:
VU metersPROGRAMMABLEKEYSMAINSCREEN
Page 14 and 15:
At most, the last line will have fo
Page 16 and 17:
• The three rotary encoders, from
Page 18 and 19:
2.1.3. Wrist- rest and side trims.A
Page 20 and 21:
2.2.1. Power supply.The power suppl
Page 22 and 23:
• Maximum power: 100mW at 40 ° C
Page 24 and 25:
2.2.2.3. Control and studio monitor
Page 26 and 27:
- Opening the unit.It’s VERY IMPO
Page 28 and 29:
Digital input 4 Digital input 3 Dig
Page 30 and 31: “ANALOG IN 1-4” connectorPin Si
Page 32 and 33: MIC/LINE input 4 MIC/LINE input 3 M
Page 34 and 35: 2.2.4.2. CA33 telephone hybrid opti
Page 36 and 37: 3. DESCRIPTION OF THE INTERNAL MENU
Page 38 and 39: • “CHRONO”: enables you to co
Page 41 and 42: • “BACK”: pressing this key a
Page 43 and 44: 3.4.3. “SELECT“ menu.This menu
Page 45 and 46: The “Compressor / Limiter” func
Page 47 and 48: In addition, the threshold must be
Page 49 and 50: • In mic/line channels, indicatio
Page 51 and 52: • Indication of audio signal type
Page 53 and 54: Only the users defined as administr
Page 55 and 56: There are two distinct areas in thi
Page 57 and 58: The “Unlock” button allows you
Page 59 and 60: The lower part of the “User Confi
Page 61 and 62: 4.2.1. “Board Configuration” su
Page 63 and 64: o“TH02”: GPI to accept the part
Page 65 and 66: The mixer bus configuration table h
Page 67 and 68: 4.2.3.1. Advanced configuration of
Page 69 and 70: • “Mono”: allows you to defin
Page 71 and 72: 4.2.4.1. “Studio Room Section“.
Page 73 and 74: 4.3. “Programmable Configuration
Page 75 and 76: 4.3.2. “Programmable Keys” subm
Page 77 and 78: • “Latch Mode”: allows you to
Page 79: 4.3.2.4. Configuration of “Codec
Page 83 and 84: The lower part of the “Programmab
Page 85 and 86: The three buttons at the bottom of
Page 87 and 88: Allows you to scroll to the top of
Page 89 and 90: • “ATTACK TIME”: this is the
Page 91 and 92: 4.3.4.4. Advanced configuration of
Page 93 and 94: The available options in the snapsh
Page 95 and 96: From left to right and from top to
Page 97 and 98: 4.4. “Firmware Upgrade” menu.Th
Page 99 and 100: In case you select an AFU file that
Page 101 and 102: 5. A.E.Q. GUARANTEE.AEQ warrants th
show all

Manual - AEQ International

Create successful ePaper yourself

Delete template?

Save as template?