Rover 214 & 414 Service and Repair Manual - Rover club
Rover 214 & 414 Service and Repair Manual - Rover club
Rover 214 & 414 Service and Repair Manual - Rover club
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
12•10 Body electrical systems<br />
6.13a Instrument panel illumination<br />
bulbholder is a twist fit in panel . . .<br />
13 All bulbs, with the exception of the main<br />
panel illumination bulb, are integral with their<br />
holders. The main panel illumination bulb is of<br />
the capless type <strong>and</strong> is a push fit in its holder<br />
(see illustrations). Be very careful to ensure<br />
that the new bulbs are of the same rating as<br />
those removed as this is especially important<br />
in the case of the ignition/battery charging<br />
warning lamp.<br />
14 Refitting is the reverse of the removal<br />
procedure.<br />
Facia illumination bulbs<br />
15 To renew the various facia illumination<br />
bulbs, it will first be necessary to remove the<br />
relevant facia panel to gain access to the<br />
bulb.<br />
Switch illumination bulbs<br />
16 All of the facia panel switches are fitted<br />
7.3a Remove headlamp retaining screws<br />
(remaining one arrowed) . . .<br />
7.4 Disconnecting headlamp wiring<br />
connector<br />
6.13b . . . bulb being of capless type<br />
with illuminating bulbs. Some are also fitted<br />
with a bulb to show when the circuit<br />
concerned is operating. These bulbs are an<br />
integral part of the switch assembly <strong>and</strong><br />
cannot be obtained separately. Bulb<br />
replacement will therefore require renewal of<br />
the complete switch assembly.<br />
7 Exterior lamp units -<br />
removal <strong>and</strong> refitting 4<br />
Note: Disconnect the battery negative lead<br />
before removing any lamp unit, <strong>and</strong> reconnect<br />
the lead after refitting the lamp.<br />
Headlamp<br />
1 Open up the bonnet, then undo the four<br />
screws securing the radiator grille to the<br />
7.3b . . . <strong>and</strong> two headlamp retaining bolts<br />
7.14 Disconnect wiring connector (A) <strong>and</strong><br />
remove rear lamp unit retaining nuts (B)<br />
1689 <strong>Rover</strong> <strong>214</strong> & <strong>414</strong> Updated Version 09/97<br />
headlamps <strong>and</strong> remove the grille from the<br />
vehicle.<br />
2 Remove the screw securing the indicator<br />
lamp assembly to the wing <strong>and</strong> position the<br />
lamp unit clear of the headlamp assembly.<br />
3 Undo the two headlamp retaining screws<br />
situated behind the indicator lamp <strong>and</strong> undo<br />
the two upper headlamp retaining bolts (see<br />
illustrations).<br />
4 Disconnect the headlamp wiring connector<br />
(see illustration).<br />
5 Gently pull the headlamp upwards to<br />
release it from its lower retainer, then remove<br />
the headlamp <strong>and</strong> lower finisher trim panel<br />
assembly from the vehicle.<br />
6 If necessary, the lower finisher can be<br />
removed from the headlamp by removing the<br />
retaining screw <strong>and</strong> releasing the two<br />
retaining clips.<br />
7 Refitting is a reversal of the removal<br />
procedure. On completion adjust the<br />
headlamp beam.<br />
Front direction indicator<br />
8 Open up the bonnet <strong>and</strong> remove the<br />
indicator lamp upper retaining screw.<br />
9 Withdraw the lamp unit from the wing, then<br />
twist the bulbholder in an anti-clockwise<br />
direction to free it from the lamp <strong>and</strong> remove<br />
the lamp unit from the vehicle.<br />
10 Refitting is the reverse of the removal<br />
procedure.<br />
Front direction indicator side<br />
repeater<br />
11 Push the lamp unit towards the right to<br />
free its retaining clips then withdraw it from<br />
the wing.<br />
12 Pull the bulbholder out <strong>and</strong> remove the<br />
lamp from the vehicle.<br />
13 Refitting is a reverse of the removal<br />
procedure.<br />
Rear lamp cluster<br />
14 Working from within the luggage<br />
compartment, remove the relevant rear lamp<br />
cover <strong>and</strong> disconnect the lamp wiring<br />
connector (see illustration).<br />
15 Undo the four nuts securing the lamp unit<br />
to the body <strong>and</strong> remove the unit from the<br />
vehicle. Note the rubber seal which is fitted<br />
between the lamp unit <strong>and</strong> body (see<br />
illustration).<br />
7.15 Withdraw rear lamp unit noting<br />
rubber seal