WSCAD 5.2 - FTP Directory Listing

More documents

Recommendations

Info

Getting Started Terminal chart The terminal chart lists all the terminals in the diagram in summary form. On the initial run the following dialog appears to determine the way of sorting: If 'By Co-ordinates' is set, the terminals are listed in the order as they were drawn (1,2,3,PE,4...). If 'Alphabetical' is set, the terminals are sorted by pin number (1,2,...,PE,PE). Click on 'All terminal strips', to create the terminal chart of all terminal strips and to store the list as a drawing in your project directory. Hint Do not forget that the Demo version has a very limited output capability. Cable list A further automatic function is to create a cable list which includes all the cables in the drawing set with cable names and types, destination names etc. Again, the graphical form design allows a maximum flexibility. The following menu appears when you start the full project analysis for the first time: Select 'cable name' as the sort option. 114
Cable chart Automated listings The cable chart is a list containing a variety of information on the individual cable conductors and the components to which these are connected. Hint You do not need to enter any data yourself. Wiring chart The wiring chart lists all the individual wires (point to point connections) in the schematic. Each individual connection is listed, with information on the first destination (connection to component 1) and the second destination (connection to component 2) including connection name, cross section, conductor colour and length. The following menu appears on the initial run: Set the sort option to 'Line name' and click 'Start'. All the connections in the schematic will be listed. 115
Page 1 and 2:
WSCAD 5.2 Getting Started © Copyri
Page 3 and 4:
Table Of Contents Introduction.....
Page 5 and 6:
Introduction General Introduction W
Page 7:
Introduction The 'WebHelp' is alway
Page 10 and 11:
Getting Started Text find/replace -
Page 12 and 13:
Getting Started Creation helping li
Page 14 and 15:
Getting Started With the Demo versi
Page 16 and 17:
Getting Started The mouse pointer/c
Page 18 and 19:
Getting Started 16 The status displ
Page 20 and 21:
Getting Started General In addition
Page 23 and 24:
Design capture General In this chap
Page 25 and 26:
Design capture The project 'WSCAD e
Page 27 and 28:
Creating new pages for a drawing se
Page 29 and 30:
Design capture Four Drawing sheets
Page 31 and 32:
Design capture You will see this st
Page 33 and 34:
Placing Components General In WSCAD
Page 35 and 36:
Design capture The 'Symbol Explorer
Page 37 and 38:
Placing symbols with database Inter
Page 39 and 40:
Design capture Select '1LA7083-6AA1
Page 41 and 42:
Design capture Now place another mo
Page 43 and 44:
Design capture You can also modify
Page 45 and 46:
Terminal browser Design capture To
Page 47 and 48:
Input via Terminal Number Interesti
Page 49 and 50:
Hint Design capture Circuit diagram
Page 51 and 52:
Design capture The Contactor list d
Page 53 and 54:
Design capture For the assignment o
Page 55 and 56:
Design capture Make no changes in t
Page 57 and 58:
Contactor Manager symbols Symbol De
Page 59 and 60:
Contact Design capture the '!'. Now
Page 61 and 62:
Mark all coils (-Q..) Design captur
Page 63 and 64:
Design capture After OK button the
Page 65 and 66: Design capture Exit the Contactor B
Page 67 and 68: Design capture Position the cursor
Page 69 and 70: Design capture In the appearing PLC
Page 71 and 72: Hint Design capture Obviously we wo
Page 73 and 74: Modifying the PLC byte address Func
Page 75 and 76: Inserting connections (destination
Page 77 and 78: Inserting corners This button activ
Page 79 and 80: Naming lines General This function
Page 81 and 82: Design capture Enter 'P11' as the l
Page 83 and 84: Finally, go back to page 1 of the d
Page 85 and 86: Design capture Click 'New' to load
Page 87 and 88: Design capture Draw another cable l
Page 89: Design capture Now select the objec
Page 92 and 93: Getting Started First select the me
Page 94 and 95: Getting Started For the 'Output sty
Page 96 and 97: Getting Started Inserting component
Page 98 and 99: Getting Started Exit the dialog wit
Page 100 and 101: Getting Started Position the cabine
Page 102 and 103: Getting Started The first component
Page 104 and 105: Getting Started Select the number '
Page 106 and 107: Getting Started Hint Please ensure
Page 108 and 109: Getting Started Repeat this process
Page 111 and 112: Automated listings General In WSCAD
Page 113 and 114: Automated listings Via the 'File de
Page 115: Project data Automated listings The
Page 119 and 120: Accept the default settings and sta
Page 121: Hint Automated listings Remember th
Page 124 and 125: Getting Started Now you are going t
Page 126 and 127: Getting Started (i.e. cross referen
Page 128 and 129: Getting Started By entering into a
Page 130 and 131: Printout of important drawings 128
Page 132 and 133: Getting Started 130
Page 144: Getting Started 142
show all

WSCAD 5.2 - FTP Directory Listing

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?