20.08.2013 Views

HP 8648 A/B/C/D - Changpuak.ch

HP 8648 A/B/C/D - Changpuak.ch

HP 8648 A/B/C/D - Changpuak.ch

SHOW MORE
SHOW LESS

You also want an ePaper? Increase the reach of your titles

YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.

RF Level Accuracy Performance Test<br />

Configure the<br />

<strong>HP</strong> <strong>8648</strong>B/C/D<br />

Measure High Level<br />

Power Accuracy<br />

(5 13 dBm)<br />

Note<br />

Configure the<br />

<strong>HP</strong> <strong>8648</strong> Option 1EA<br />

1. Connect the power sensor to the <strong>HP</strong> <strong>8648</strong> RF OUTPUT connector.<br />

2. Set the amplitude; press CAMPLITUDE] (13) [dB(m).<br />

3. Turn the RF output on; press Cm].<br />

1. Enter the frequencies and power levels shown in the test record.<br />

Make sure the power sensor cal factors are entered correctly for<br />

ea<strong>ch</strong> frequency. Do not test below -20 dBm with this test setup.<br />

2. Record the test results and compare the results to the limits in the<br />

test record.<br />

<strong>HP</strong> <strong>8648</strong>B . . . . . . . . . . . . . . . . . . . . . . . . . . . .‘l%ble 8-38<br />

<strong>HP</strong> <strong>8648</strong>C . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 8-63<br />

<strong>HP</strong> <strong>8648</strong>D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Table 8-88<br />

For <strong>HP</strong> <strong>8648</strong>B/C/D instruments without Option lEA, high power, skip<br />

ahead to “Configure the Power Meter”. All others, continue with the<br />

next step.<br />

1. Set the amplitude; press [AMPLITUDE) lloJ m.<br />

2. Turn the RF output on; press (RF).<br />

3. Connect the power sensor directly to the <strong>HP</strong> <strong>8648</strong> RF OUTPUT<br />

connector.<br />

Measure the High 1. Measure the RF power at ea<strong>ch</strong> frequency listed in Table 8-l and<br />

Power Level Accuracy record the measurement in the first row of the table.<br />

8-24 Performance Tests<br />

2. Connect the 10 dB attenuator between the <strong>HP</strong> <strong>8648</strong> RF OUTPUT<br />

connector and the power sensor.<br />

3. Measure the RF power at ea<strong>ch</strong> frequency listed in Table 8-l and<br />

record the measurement in the second row of the table.<br />

4. Calculate the actual attenuator value for ea<strong>ch</strong> frequency (the<br />

difference between the two measurements) and record it in the<br />

third row of the table.<br />

5. For ea<strong>ch</strong> frequency listed in Table 8-l set the <strong>HP</strong> <strong>8648</strong> amplitude<br />

to the level shown in the table and measure the RF power level<br />

through the 10 dB attenuator. Record the measurement in the fifth<br />

row of the table.<br />

6. Calculate the actual output power for ea<strong>ch</strong> frequency (the sum of<br />

the measured power and the attenuator value) and record it in the<br />

test record.

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!