STANDARD HANDBOOK OF PETROLEUM & NATURAL GAS ...

~
--
---
Drill String: Composition and Design 751
Table 4-84
(continued)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
DRILL PIPE
TOOL JOINT
J0l"t TOd
D..ip".tio"l
7
Sirrand Nom. Gnrde- 0ut.Y~ Inside Bed Total Pin Box chn- Di. Di. Tor-
Dis Diu Disd lannh Tons s~.- bind 01 Pin dBox swnd
StYl. Ib \VLZ -2
of Pin of Pin3 Pinand Tml SD~E. ZX lrnnh at Eie st Elc Ratio.
fl and fl164 Box Joint of and -.for vamr
Pan Umet. Umt. Pin 10
Box -113ZShou1d~1. Pm
ZI/SY *I164
Box Mnr Max Drill
':t ? Y, PiM
D d DP LP LP. L, L Des Dm
EO(4WIF) 4%EU 16.60 E75 636* 3%* 51% 11% 7 10 17 5 5 1.23
X95 6%* 3%. 5%f 11% 7 10 17 5 5 .97
G105 6%' 3%. 5%: 11% 10 17 5 5 .38
S135 6%' 3% 5%1 11% , 10 17 5 5 .81
4% EU 20.00 E75 6%* 3%. 54% 11% I 10 17 5 5 1.02
X95 6%' 3% 5%E 11% 7 10 17 5 5 .96
G105 6%- 3% 5%f 11% I 10 17 5 5 36
S135 6% 3 5%f 11% 'I 10 17 5 5 .87
5 IEU 19.50 E75 6%' 3%' 51% 11% 7 10 17 5% 5% .92
X95 6%. 3% 5@$ 11% 7 10 17 5% 5% .86
G105 6% 3% 5%Y 11% 7 10 17 5% 5% .89
5135 6% 2% 51t 11% 7 10 17 5% 5% .86
5 IEU 25.60 E76 6%' 3% 51t 11% 7 10 17 5% 5% .86
X95 6% 3 50f 11% 7 10 17 5% 5% .86
G105 6% 2% 5$4 11% 7 10 17 5% 6% .87
5% FH-' 5 IEU 19.50 E75 7' 3% 68: 13 8 10 18 5% 5% 1.53
X95 7* 3% 618 13 8 10 18 5% 5% 1.21
GI05 7* 3% 632 13 8 10 18 5% 5% 1.09
Si35 7% 3% 603 13 8 10 18 5% 5% .98
5 IEU 25.60 E75 7' 3% 63: 13 8 10 18 5% 5% 1.21
X95 7' 3% 611 13 8 10 18 5% 5% .95
G106 7% 3% 61: 13 8 10 18 5% 5% .99
S135 7% 3% 6:: 13 8 10 18 5% 5% .83
5% IEU 21.90 E75 7' 4 63; 13 8 10 18 5fl 5ft 1.11
X95 lo 3% 611 13 8 10 18 5tl 51t .98
G105 7% 3% 61: 13 8 10 18 5tt 5tt 1.02
S135 7% 3 72. 13 8 10 18 5th 5fh .96
5HIEU 24.70 E75 IC 4* 6:; 13 8 10 18 5ft 5fb .99
X96 7% 3% 631 13 8 10 18 5t3. 5th 1.01
G105 7% 3% 603 13 8 10 18 5th 5fh .92
5135 7% 3 73!1 13 8 10 18 5tt 5th .86
Wenotea standard OD or standard ID.
"Obsolexent connection.
'The tool joint designation (el. 1) indiutcs the sire and rtyle of the appliuble eonneetion:
2)l'ominsd weights, thread. and eoIIplings. (Col. 8) are shown for the PUrpI of identieutlon in ordering.
>The inside diameter (Col. 6) don not apply to box memben, which optn0n.l with the manulactUTer.
-1Lcngth of pin thread mdueed to S% inches (34 inch ahort) to Meommod+ S inch ID.
NOTE 1: Neck diimcten (Dn &, Dn) and inside diameters (d) o! fool joint. prior to welding are st mmulaeturer'a
option. The above tabla spsifiea fimshui dimensions after find maehming of the assembly.
NOTE 2: Appendix H eont.in. mom dimmaions of obsolescent eonnectiona and for wusre elantor louiden.
NOTE 3: No torsional ratio (tool joint pin to drill pipe) lesa then 0.80 is shown. In particuhr .mu, tool joints hmvin*
much amrller torsions1 yields may prove to be ndeguate.
--