STANDARD HANDBOOK OF PETROLEUM & NATURAL GAS ...

6.85
9.50
Table 4-86
Selection Chart-Tool Jolnts Applied to Lightwelght Drill Plpe-Grade E [30]
DRlU PIPE DATA - TOOL JOlM ATTAcHeD MOL JOINT DATA MECHANICAL PROPERTIES
To? sP= Tdc Yidd
TW*Od Ydd
in. Ib M b
Nom. W*
M.X.
Wt. Wt. I.D.
O.D. Drift
09. 19.
Tool
Tool
b/lt blrt (1) in. Type in. Dn Conn. in. in. BOX Pin Pipe(2) Joint (3) Pipe (4) Joint (5)
4.85 5.15 1.995 EU 2 9/16 1.688 NC26(I.F.) 3 3/8 1314 7 6 91820 323760 4760 6800
4.94 EO 29/16 1.850 SL-H'H) 3 114 1.995 7 6 97820 204550 4760 5500
4.87 EU 29/16 1.807 OH. 3 118 2 7 6 97820 206400 4760 4400
5.09 EU 2 9/16 1.807 W.O. 3 318 2
7 6' 97820 205920 4760 4500
7.33 2.441 EU
6.91 EU
6.91 EU
7.25 EU
10.39 2.992 EU
10.12 EU
9.95 EU
10.2s EU
3 3/16 2.063 NC31(l.F.)
3 3/16 2.296 S.L.-H9O
33/16 2.253 OH.
3 3/16 2.253 W.O.
3 7/8 2.563 NC38U.F.)
3 718 2.847 S.L.490
3 718 2.804 O.H.
3 718 2.804 W.O.
4 1/8
3 718
3 314
3 78
4 314
4 518
4 112
4 3/4
2 118
2.441
2 7/16
2 7/16
2 11/16
2.992
3
3
8
8
8
8
9 112
9 112
9 112
9 1/2
6' 135900 459120
6 135900 259180
6 135900 224040
6' 135900 289080
7' 194260 602160
6 112194260 370970
7 194260 392280
7' 194260 434400
8070
8070
8070
8070
14120
14120
14120
14120
12000
7600
5800
7500
18700
13200
11800
I3400
11.85
13.75
13.09 3.476 IU
13.13 EU
12.16 EU
13.03 EU
15.24 3.958 IU
14.98 EU
14.10 EO
14.90 EU
43/16 2.688 H90
4 112 3.125 NC46U.F.)
4 112 3.287 O.H.
4 112 3.287 W.O.
4 11/16 3.125 H90
5 3.625 NC5WI.F.)
5 3.770 O.H.
5 3.770 W.O.
5 112
5 314
5 114
5 314
6
6 I/8
5 314
6 18
2 13/16
3 114
3 15/32
3 7/16
3 l/4
3 314
3 31/32
3 718
10
10
10
10
10
10
IO
10
7 230750 913680
7. 230750 918960
7 230750 621960
7' 230750 801120
7 270030 938280
7. 270030 958920
7 270030 559440
7' 270030 868920
*If weight is of paramount importance, these connections can be supplied with a smaller O.D. or shorter tong space on box and pin, or a combination of the two to afford miximum
weight redudon without sacrificing safety in the joint. However, where possible, the manufacturers recommend ordering the joints shown to obtain the niaximum economial
tool joint service.
Otha tool jointrircs to accommodate rpecirl situations can be furnished on request.
1 T d Joint Plus 29.4' of Drill Pipe.
2 Tensile Yield Stmn(th of Drill Pipe Baed on 75,000 psi.
3 Tensile Yield Strcnith of the Tool Joint Pin is based on I20,OOO Psi Yield and the Croa Sectional Area a1 the Root of the Thread 51s inch from the Shoulder.
4 Torrional Yield Strength of the Drill Pipe ia Baaed on a Shear Strenglh of 5l.lqbof the Minimum Yield Strength.
5 Tonionsl Yield Strenglh ofthe Tool Joint Bawd on Tensile Yleld Strength of the Pin and Compressive Yield Strength of the Box - owe st Value Prevailing.
19440
19440
19440
19440
25860
25860
25860
25860
3s500
34100
22100
29300
37400
37900
21 100
34100
8
3
a
0
E.
g.
3
w
3
a
U
a
5'
1