Blackmagic ATEM Manual - Concept Music Art

More documents

Recommendations

Info

100 Blackmagic UltraScope Zoom Function Blackmagic UltraScope allows you to zoom in on various displays for a more detailed analysis. This helpful function will also pan and zoom the graticules for each display in high resolution. The zoom function is available in the Parade, Waveform, Vectorscope and Picture displays. To zoom in, simply click on the bottom right of each respective display. Now you will be able to view the display in finer detail. Drag the mouse within the display area to pan around the zoomed display. Clicking again, will return the display back to its normal view. Zoom button
101 Blackmagic UltraScope Color Correction Terminology Blacks – black levels in the video signal Mids – mid-gray levels in the video signal Whites – white levels in the video signal 1. Parade Display Parade Display is perfect for color-correction, checking for illegal colors and checking levels. When color-correcting, press the RGB button to display the full height of each color channel as red, green and blue. Monitoring the levels of each red, green and blue color channel makes color-correction straightforward and it is easy to view color balance in the blacks, mids and whites of the video signal. Parade Display enables you to identify details common to the red, green and blue channels, making it simple to color-balance and remove unwanted color tints. It’s often important when color-correcting to make sure you’re not clipping the video levels. Make sure the video is full level but not clipped. You can turn on the GAMUT function, and any illegal levels will be highlighted in bright red, so they are easy to see. Instructions for setting gamut limits can be found in the Error Logging Display section of this manual. If you want to increase the video level, then make sure it doesn’t go above upper RGB limit or you will encounter illegal levels. Some equipment won’t let you generate illegal 100% RGB levels, however other equipment will. Blackmagic UltraScope lets you see illegal levels whenever they occur. Illegal video can also happen in blacks as well as whites. In some color-correction systems, black levels can be lowered to below the black point of 0%. The levels will be shown as bright red if this falls below the lower gamut limit and the GAMUT warning mode is enabled. If you observe illegal black levels, just add some “lift” or gain to eliminate them but check the 100% graticule level to make sure the whole video signal has not lifted and generated illegal colors in the whites. It’s a constant adjustment process, when color-correcting, to attain the best looking images without generating illegal levels! To check levels, simply press the YUV or YUV+ button. The COLOR setting switches the RGB display to color rather than traditional black and white. When the COLOR setting is used with the YUV or YUV+ display, luma (brightness) remains white, B-Y (difference between blue and luma) appears blue and R-Y (difference between red and luma) appears red. The COLOR setting is not a professional setting and should usually be switched off, especially when showing video to clients.
Page 1 and 2:
Installation and Operation Manual A
Page 3 and 4:
Contents ATEM Production Switchers
Page 5 and 6:
5 Getting Started Introducing ATEM
Page 7 and 8:
7 Getting Started Another great adv
Page 9 and 10:
9 Getting Started Plugging in Multi
Page 11 and 12:
11 Getting Started Installing Black
Page 13 and 14:
13 Getting Started Plugging in your
Page 15 and 16:
15 Getting Started Plugging in Came
Page 17 and 18:
17 Getting Started ATEM Setup Utili
Page 19 and 20:
19 Getting Started Change Network S
Page 21 and 22:
21 Getting Started GPI and Tally In
Page 23 and 24:
23 Updating the Software How to upd
Page 25 and 26:
25 Connecting Video Outputs There a
Page 27 and 28:
27 Using ATEM Software Control Inte
Page 29 and 30:
29 Using ATEM Software Control Swit
Page 31 and 32:
31 Using ATEM Software Control Fade
Page 33 and 34:
33 Using ATEM Software Control Medi
Page 35 and 36:
35 Using ATEM Software Control ATEM
Page 37 and 38:
37 Using ATEM Software Control Sett
Page 39 and 40:
39 Using ATEM Software Control Cust
Page 41 and 42:
KEY 1 KEY 2 KEY 3 KEY 4 4 5 6 LUMA
Page 43 and 44:
1 2 3 4 5 6 43 7 8 9 Using the ATEM
Page 45 and 46:
45 Operating Your ATEM Switcher Int
Page 47 and 48:
47 Operating Your ATEM Switcher Cut
Page 49 and 50: 49 Operating Your ATEM Switcher Aut
Page 51 and 52: 51 Operating Your ATEM Switcher To
Page 53 and 54: 53 Operating Your ATEM Switcher Tra
Page 55 and 56: 55 Operating Your ATEM Switcher Wip
Page 57 and 58: 57 Operating Your ATEM Switcher To
Page 59 and 60: 59 Operating Your ATEM Switcher The
Page 61 and 62: 61 Operating Your ATEM Switcher Sha
Page 63 and 64: 63 Operating Your ATEM Switcher Sof
Page 65 and 66: 65 Operating Your ATEM Switcher Man
Page 67 and 68: 67 Operating Your ATEM Switcher Key
Page 69 and 70: 69 Operating Your ATEM Switcher Bac
Page 71 and 72: 71 Operating Your ATEM Switcher Ups
Page 73 and 74: 73 Operating Your ATEM Switcher Chr
Page 75 and 76: 75 Operating Your ATEM Switcher Adj
Page 77 and 78: 77 Operating Your ATEM Switcher Adj
Page 79 and 80: 79 Operating Your ATEM Switcher Add
Page 81 and 82: 81 Operating Your ATEM Switcher Key
Page 83 and 84: 83 Operating Your ATEM Switcher Usi
Page 85 and 86: 85 Operating Your ATEM Switcher Usi
Page 87 and 88: 87 Operating Your ATEM Switcher Med
Page 89 and 90: 89 Blackmagic Media Express What is
Page 91 and 92: 91 Blackmagic Media Express Media L
Page 93 and 94: 93 Blackmagic Media Express Media L
Page 95 and 96: 95 Blackmagic Media Express Browsin
Page 97 and 98: 97 Blackmagic UltraScope What is Bl
Page 99: 99 Blackmagic UltraScope Full Scree
Page 103 and 104: 103 Blackmagic UltraScope 3. Vector
Page 105 and 106: 105 Blackmagic UltraScope From the
Page 107 and 108: 107 Blackmagic UltraScope 6. Audio
Page 109 and 110: 109 Help Getting Help The fastest w
Page 111 and 112: 111 Help Which notebooks can I use
show all

Blackmagic ATEM Manual - Concept Music Art

Create successful ePaper yourself

Delete template?

Save as template?