Blackmagic ATEM Manual - Concept Music Art
Blackmagic ATEM Manual - Concept Music Art
Blackmagic ATEM Manual - Concept Music Art
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
1<br />
2 3<br />
4 5 6<br />
43<br />
7 8 9<br />
Using the <strong>ATEM</strong> 1 M/E Broadcast Panel<br />
0 CLR<br />
CAM<br />
CUT<br />
FILL<br />
SHIFT<br />
ON ON ON ON<br />
BKGD KEY 1 KEY 2 KEY 3 KEY 4<br />
DIP<br />
DVE<br />
MIX<br />
WIPE<br />
DSK 1<br />
TIE<br />
DSK 1<br />
CUT<br />
DSK 2<br />
TIE<br />
DSK 2<br />
CUT<br />
Next Transition<br />
The BKGD, KEY 1, KEY 2, KEY 3, KEY 4 buttons are used to select the elements which will transition on air<br />
or off air with the next transition. Any combination of background and keys can be selected by pressing<br />
multiple buttons simultaneously.<br />
Pressing any of the next transition buttons will clear selection of all others. When selecting the elements of<br />
the next transition, the switcher operator should look at the preview output because it provides an accurate<br />
representation of what the program output will look like after the transition is completed. When only the<br />
BKGD button is selected, a transition from the current source on the program bus to the source selected on<br />
the preview bus will occur.<br />
1<br />
PREV<br />
TRANS<br />
2 3<br />
CUT<br />
4 5 6<br />
AUTO<br />
DSK 1<br />
AUTO<br />
DSK 2<br />
AUTO<br />
FTB<br />
ON AIR<br />
The ON AIR indicator buttons indicate which of the upstream keys are currently on air and can also be used<br />
to immediately cut a key on or off air.<br />
ON ON ON<br />
7<br />
CAM<br />
8 9<br />
0Transition CLR Control and<br />
Upstream Keyers<br />
Downstream Keyers<br />
DSK TIE<br />
The DSK TIE button will enable the DSK on the preview output, along with the next transition effects, and tie<br />
it to the main transition control so that the DSK can be taken to air with the next transition.<br />
Because the tied downstream keyer is now tied to the main transition, the transition will happen at the rate<br />
specified in the transition rate display of the transition control block. When the DSK is tied, the signal routing<br />
to the clean feed 1 is unaffected.<br />
E<br />
KEY 2 KEY 3 KEY 4<br />
DSK 1<br />
TIE<br />
DSK 2<br />
TIE<br />
DSK CUT<br />
The DSK CUT button is used to cut the DSK on or off air and indicates whether the DSK is currently on or off<br />
air. The button is illuminated if the DSK is currently on air.<br />
DSK 1<br />
CUT<br />
DSK 2<br />
CUT<br />
DSK AUTO<br />
The DSK AUTO button will mix the DSK on or off air at the rate specified in the DSK rate window.<br />
O<br />
DSK 1<br />
AUTO<br />
DSK 2<br />
AUTO<br />
FTB<br />
Downstream Keyers and<br />
Fade to Black<br />
Fade to Black<br />
FTB<br />
The FTB button will fade the program output to black at the rate specified in the FTB rate window. Once the<br />
program output has been faded to black, the FTB button will remain illuminated red until it is pressed again,<br />
fading the program output up from black at the same rate. A fade to black cannot be previewed.