F4200N Manual - Fisnar.fr

More documents

Recommendations

Info

F4200N Operating Manual Section 4: Programming Example 9 10 11 12 13 14 15 16 17 18 19 Instruction Now jog the tip to the location of the third point (3: Arc Point). When the location is correct, press the ENTER key, then 5 to register the location as an Arc point. Jog the tip to the location of the fourth point (4: Line Passing). When the location is correct, press the ENTER key, then 3 key to register the location as a Line Passing point. Jog the tip to the location of the fifth point (5: Line Passing). When the location is correct, press the ENTER key, then 3 to register the location as a Line Passing point. Jog the tip to the location of the sixth point (6: Line Passing). When the location is correct, press the ENTER key, then 3 to register the location as a Line Passing point. Jog the tip to the location of the seventh point (7: Line End). When the location is correct, press the ENTER key, then 6 to register the location as a Line End point. The line is now complete. The next step is to register the dispense settings for the dots. Press the SETUP key, then 3 to register the dot dispensing time. Type 0.5 to register a dispensing time of 0.5 seconds, and then press ENTER. Type 0.1 to register a waiting time after dispensing of 0.1 seconds, and then press ENTER. Jog the tip to the location of first dispense dot (8: Dispense Dot). When the location is correct, press the ENTER key, then 1 to register the location as a Dispense Dot. Jog the tip to the location of second dispense dot (9: Dispense Dot). When the location is correct, press the ENTER key, then 1 to register the location as a Dispense Dot. Jog the tip to the location of third dispense dot (10: Dispense Dot). When the location is correct, press the ENTER key, then 1 to register the location as a Dispense Dot. The program is now complete. Press ENTER, then 7 to register address 13 as the END of the program. 20 To run the program, press the RUN key. ADDR:5 EMPTY ADDR:6 EMPTY ADDR:7 EMPTY ADDR:8 EMPTY ADDR:9 EMPTY Display Shows Part # 562187N Rev. C Jun 2011 PROG:10 PROG:10 PROG:10 PROG:10 PROG:10 Point Dispense Setup -------------------- Dis. Time: Tail Time: unit: sec ADDR:10 EMPTY ADDR:11 EMPTY ADDR:12 EMPTY ADDR:13 EMPTY ADDR:14 EMPTY PROG:10 PROG:10 PROG:10 PROG:10 PROG:10 - Page 26 - © 2011 Fisnar Inc.
F4200N Operating Manual Section 4: Programming Example Part # 562187N Rev. C Jun 2011 2. Good Programming Practices It is recommended to register the setup commands at the beginning of every program. The following setup commands are the most commonly used: Dispense End Setup Point Dispense Setup Line Dispense Setup Line Speed Z Clearance Retract Setup Adjust Position Setup For a complete list and description of all the different setup commands, refer to SECTION 3:4.2 F4 (Setup Menu) and SECTION 5:2 Setup Menu. - Page 27 - © 2011 Fisnar Inc.
Page 1 and 2: F4200N Operating Manual Part # 5621
Page 3 and 4: F4200N Operating Manual Table of Co
Page 5 and 6: F4200N Operating Manual Table of Co
Page 7 and 8: F4200N Operating Manual Section 1:
Page 27: F4200N Operating Manual Section 4:
Page 79 and 80:
F4200N Operating Manual Section 5:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113:
THIS PAGE INTENTIONALLY LEFT BLANK
show all

F4200N Manual - Fisnar.fr

Create successful ePaper yourself

Delete template?

Save as template?