Color iQC Help - X-Rite

More documents

Recommendations

Info

This button eliminates any sorting done and returns the data in the Tree View to its original sort order. This button copies a selected item to the data section of the Tree View. This button copies a selected item to the standard position. (Remember, only one item can be in the Standard slot at a time.) This button opens a dialog box allowing you to create a measurement. This button will average a new trial measurement based on all of the trials currently selected when the button is clicked on. This button will average a new standard based on the data currently selected when the button is clicked on. This button opens the Properties dialog box for the selected item. This button will show the selected items in the available data views. file. This button will export the currently selected items to an EXP formatted This button will export the currently selected items to a QTX formatted file. This button will export the currently selected items to a NetPalette file. This button will automatically start the formulation process and attempt to match the currently selected item. This button will sort the data on colorimetric data. 26
This button will sort the data by name. This button will export the selected data to a CXF formatted file. Settings Files and Templates It is important to understand the differences between these two program options and how they affect the operation of the system. Each is discussed below. The Settings File Users may choose how they want their settings saved, in the job or in a "settings file." The default method is to use the settings file option. However, the first time you run the software after installation you will be prompted to select the System Default Settings at which point a checkbox allows you to switch the system from using settings files back to storing that information in each job. Whichever method you select, you will still have the option to change the way in which an individual job stores its settings when running the software. The settings file option has been designed to provide an easy way to ensure continuity for the settings established for any particular type of job (i.e. quality control, formulation, correction, etc.) Multiple jobs can all point to the same settings file, providing a single source for the values governing calculations in all those jobs. Multiple settings files may be created and jobs linked to them, providing an easy way to set up for a variety of tasks while still maintaining continuity for the settings established for those tasks. One of the main advantages to using the settings file (as opposed to storing them in each job) is that it allows users to make global changes to large numbers of jobs by simply editing one settings file. For example, you have a large number of formulation jobs, each loaded with a particular standard. Previously, you had the system set up to sort the formulas on DEcmc, Predicted Performance, and Cost. However, you now need to sort formulas on Predicted Performance, Metamerism, and Cost. The settings file allows making this change easily. Simply open one of the formulation jobs and make the change in the Formula Display tab of the settings dialog, then click once on the "Save Settings" command under the Job menu. The new settings will be saved to the file. All formulation jobs pointing to that settings file will now sort their formulas on the Predicted Performance, Metamerism, and Cost. 27
Page 1 and 2: Color iMatch Textiles Help PDF file
Page 3 and 4: Getting Started Edit Default System
Page 5 and 6: Default Toolbar File --- This field
Page 7 and 8: Concentration Units --- This select
Page 9 and 10: etween a sample and the target The
Page 11 and 12: Settings Options This tab of the Se
Page 13 and 14: The image below shows the QC tab wh
Page 15 and 16: the textile industry's practice of
Page 17 and 18: The center box, within which the st
Page 19 and 20: Desktop Management Desktop Manageme
Page 21 and 22: This tab allows you to select to cr
Page 23 and 24: Change System Settings - Selecting
Page 25: Opens a dialog box which allows you
Page 29 and 30: Spectro Management Install or Confi
Page 31 and 32: 31 The third dialog in the installa
Page 33 and 34: 33 If you had a calibration file fo
Page 35 and 36: the different types of measurements
Page 37 and 38: 37 Calibration Mode Properties Dial
Page 39 and 40: A second field, deCMC Limit, allows
Page 41 and 42: You must edit the file prior to its
Page 43 and 44: one with small area view), you will
Page 45 and 46: Measuring Data from the Instrument
Page 47 and 48: In addition, some items in the Stan
Page 49 and 50: Percent When measuring primary data
Page 51 and 52: You may automatically average a set
Page 53 and 54: This option is primarily intended f
Page 55 and 56: Data Management Recalling Data from
Page 57 and 58: However, if you are using the name
Page 59 and 60: Once the possible matches to your s
Page 61 and 62: Select the data type you wish to de
Page 63 and 64: 63 Once you have selected the desir
Page 65 and 66: user groups you wish merely by typi
Page 67 and 68: Spectral Data This tab will allow y
Page 69 and 70: Tolerances Used This tab will displ
Page 71 and 72: Paste buffer to current recipe ---
Page 73 and 74: If you wish to select only a portio
Page 75 and 76: Once the item is in the “Selected
Page 77 and 78:
Y --- Represents a standard or samp
Page 79 and 80:
OJ_Index --- This index was develop
Page 81 and 82:
and third (2,3) illuminants. You ma
Page 83 and 84:
Formulation/How To Preliminaries to
Page 85 and 86:
85 Other configurations are availab
Page 87 and 88:
If you wish to view all of the form
Page 89 and 90:
In addition, a separate sort column
Page 91 and 92:
Formulation Settings/Textiles Formu
Page 93 and 94:
Evaluation --- There are two settin
Page 95 and 96:
This value controls the graphical d
Page 98 and 99:
Primary Evaluation How to Evaluate
Page 100 and 101:
place the cursor on the image until
Page 102 and 103:
Selecting the Primaries 1. Place yo
Page 104 and 105:
4. Deleted for Storage Limit -- Thi
Page 106 and 107:
Correction/How To Correct a Formula
Page 108 and 109:
Process Type allows you to select w
Page 110 and 111:
Column Three - Correction Factor [C
Page 112 and 113:
eSubmit/How To eSubmit and Extended
Page 114 and 115:
The path fields following the radio
Page 116 and 117:
Now that you have the Submit view,
Page 118 and 119:
Taper Tool/How To Setup the Taper C
Page 120 and 121:
Methods of Tapering and Grouping Li
Page 122 and 123:
122 you may let the program auto-se
Page 124 and 125:
New Job-- This command opens a new
Page 126 and 127:
Recall Settings -- This option reca
Page 128 and 129:
Status Bar -- When selected, this o
Page 130 and 131:
The second option, "Manage", brings
Page 132 and 133:
Setup SLI-Taper parameters --- This
Page 134:
134 for use. In addition, the Licen
show all

Color iQC Help - X-Rite

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?