CSI-F-10 User manual - Hydac

More documents

Recommendations

Info

GSM Radio Module CSI-F-10 Page 1029.7.6 Exclusive OrThe Exclusive Or function links the two Boolean inputs with the "xor"operation and supplies the result to its Boolean output.The output is "1" if precisely one of the two inputs is "1". If both ofthe inputs are "0" or if both of the inputs are "1", then the output willbe "0". One can also say that the output is then precisely "1" if thetwo inputs are not equal.The following log table makes this function clear.x 1 x 2 y0 0 00 1 11 0 11 1 0Inputs: x 1 : (Boolean)x 2 : (Boolean)Outputs: y: (Boolean)Parameters: -9.7.7 Not Exclusive OrThe Not Exclusive Or function links the two Boolean inputs with the"nxor" operation and supplies the result to its Boolean output.The output is "0" if precisely one of the two inputs is "1". If both ofthe inputs are "0" or if both of the inputs are "1", then the output willbe "1". One can also say that the output is then precisely "1" if thetwo inputs are equal.The following log table makes this function clear.x 1 x 2 y0 0 10 1 01 0 01 1 1Inputs: x 1 : (Boolean)x 2 : (Boolean)Outputs: y: (Boolean)Parameters: -Status 2011/08/17 HYDAC ELECTRONIC GMBH Part.-Nr.: 669752
GSM Radio Module CSI-F-10 Page 1039.8 Other Boolean Operations9.8.1 Note Switching StatusThe Note switching status function is used to hold on to a Booleanvalue (to freeze it). It has two Boolean inputs.If the input value x 2 is "1", then the input value x 1 is output at theoutput. If the input value x 2 is "0", then the last output value remainsin effect.If the value is only to be applied for one flank, then you can put thefunction Pulse generation upstream at x 2 (see Chap. 9.8.6).Inputs: x 1 : Value (Boolean)x 2 : Note (Boolean)Outputs: y: (Boolean)Parameters: -9.8.2 Switching DelayThe Switching delay function is used to delay Boolean signals. Thefunction has one Boolean input and one Boolean output. A changeat the input will not be recognizable at the output until after aparameterizable delay time has elapsed.The delay times can be set separately for switching on andswitching off. They are adjusted with the parameters Switch-ondelay and Switch-off delay. This makes it possible to hide short-termsignal changes from view.Example:Input and output are "0", the switch-on delay is set to 5 seconds. Ifthe input switches now to "1", then the output waits 5 secondsbefore switching to "1". If the input switches back to "0" before the 5seconds have elapsed, then the input remains set to "0" and thechange at the input is not visible at all at the output.Inputs: x: (Boolean)Outputs: y: (Boolean)Parameters: p 1 : Switch-on delay in seconds (Numerical)p 2 : Switch-off delay in seconds (Numerical)Status 2011/08/17 HYDAC ELECTRONIC GMBH Part.-Nr.: 669752
Page 1 and 2:
GSM Radio ModuleCSI-F-10User Manual
Page 3 and 4:
GSM Radio Module CSI-F-10 Page 3Tab
Page 5 and 6:
GSM Radio Module CSI-F-10 Page 59.2
Page 7 and 8:
GSM Radio Module CSI-F-10 Page 711.
Page 9 and 10:
GSM Radio Module CSI-F-10 Page 91 G
Page 11 and 12:
GSM Radio Module CSI-F-10 Page 112
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
GSM Radio Module CSI-F-10 Page 21Co
Page 23 and 24:
GSM Radio Module CSI-F-10 Page 23PI
Page 25 and 26:
+U BGNDGSM Radio Module CSI-F-10 Pa
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52: GSM Radio Module CSI-F-10 Page 516.
Page 55 and 56: GSM Radio Module CSI-F-10 Page 55
Page 101: GSM Radio Module CSI-F-10 Page 1019
Page 119 and 120: GSM Radio Module CSI-F-10 Page 119S
show all

CSI-F-10 User manual - Hydac

Create successful ePaper yourself

Delete template?

Save as template?