CSI-F-10 User manual - Hydac

More documents

Recommendations

Info

GSM Radio Module CSI-F-10 Page 849.2.6 Time SensorThe Time sensor is a function which generates a pulse at anadjustable interval (e.g. every minute, every 5 minutes), thus settingits Boolean output to "1" for a cycle and then back to "0".The following settings are possible for the Interval parameter:• 1; 2; 5; 10; 15; 30 Seconds,• 1; 2; 5; 10; 15; 30 Minutes,• 1; 2; 6; 12; 24 Hours.At the same time the output pulse is always synchronized with thetime of day. If, for example, "6 hours" is set, then a pulse will begenerated at 0600 HRS, 1200 HRS, 1800 HRS and 2400 HRS.If a pulse is required at particular times of the day, then you shoulduse a clock timer with a downstream pulse generator instead of atime sensor (see Chap. 9.8.6).Inputs: -Outputs: y: (Boolean)Parameters: p 1 : Interval (input list)9.2.7 Clock TimerThe Clock timer is a function which switches on its Boolean output ata certain time during a month and then switches it off again at adifferent point in time.The switch-on time is set using the parameters Switch-on day andSwitch-on time, while the switch-off time is set using the parametersSwitch-off day and Switch-off time.A weekday "Monday" to "Sunday" can be set. The setting "Daily" isalso possible. The "Daily" setting is only possible if both days are setto "Daily". The Editor prevents erroneous inputs: If, for example, theswitch-on day is changed from "Monday" to "Daily", then the switchoffday is automatically set to "Daily".If switch-on time and switch-off time are identical, then the outputwill be switched on for precisely this specified second.If only one pulse is required, i.e. if the output in intended to be set forexactly one cycle to "1" and then back to "0", then use adownstream pulse generator (see Chap. 9.8.6).Inputs: -Outputs: y: (Boolean);Parameters: p 1 : Switch-off day (input list)p 2 : Switch-off time (time of day)p 3 : Switch-on day (input list)p 4 : Switch-on time (time of day)Status 2011/08/17 HYDAC ELECTRONIC GMBH Part.-Nr.: 669752
GSM Radio Module CSI-F-10 Page 859.2.8 Error EventError handling can be implemented with the function Error event.The Boolean output is switched to "1" when an error condition ispresent. The output is switched back to "0" if the error disappears.The type of error event can be set with the Event parameter.The following events are possible:Below signal rangeA sensor has a cable break, for exampleAbove signal rangeThe signal of one sensor is above the signal rangeIncorrect sensor constellationThere is either no sensor, or an incorrect sensor connected to onesensor connection port.Numerical errorAn error occured during a calculation, e.g. division by 0 or squareroot of a negative number, logarithm of 0, etc.Cycle time exceededThe set cycle time was exceeded.Inputs: -Outputs: y: (Boolean)Parameters: p 1 : Event (input list)9.2.9 Boolean ConstantsThe Boolean Constant function supplies a Boolean value which isdefined in the Editor and which does not change during the runningtime. That means that the parameter entered in the Editor is outputduring the running time at the output.Inputs: -Outputs: y: (Boolean)Parameters: p 1 : Value (Boolean)Status 2011/08/17 HYDAC ELECTRONIC GMBH Part.-Nr.: 669752
Page 1 and 2:
GSM Radio ModuleCSI-F-10User Manual
Page 3 and 4:
GSM Radio Module CSI-F-10 Page 3Tab
Page 5 and 6:
GSM Radio Module CSI-F-10 Page 59.2
Page 7 and 8:
GSM Radio Module CSI-F-10 Page 711.
Page 9 and 10:
GSM Radio Module CSI-F-10 Page 91 G
Page 11 and 12:
GSM Radio Module CSI-F-10 Page 112
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
GSM Radio Module CSI-F-10 Page 21Co
Page 23 and 24:
GSM Radio Module CSI-F-10 Page 23PI
Page 25 and 26:
+U BGNDGSM Radio Module CSI-F-10 Pa
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34: GSM Radio Module CSI-F-10 Page 33
Page 35 and 36: GSM Radio Module CSI-F-10 Page 356.
Page 83: GSM Radio Module CSI-F-10 Page 839.
Page 119 and 120: GSM Radio Module CSI-F-10 Page 119S
show all

CSI-F-10 User manual - Hydac

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?