CSI-F-10 User manual - Hydac

More documents

Recommendations

Info

GSM Radio Module CSI-F-10 Page 949.4.10 Tabular IndexThe Tabular index function is the counterpart to the Tabular valuefunction. The input value is sorted into a parameterizable numericaltable, which must be organized in order of increasing values, andthe number of the tabular entry is output.If, for example, the first tabular entry is 4 and the second is 7.8, thena 0 will be output for all input values less than 4, the value 1 will beoutput for all values between 4 and 7.8, and the value 2 for allvalues greater than 7.8.The table is defined using the Table parameter. Each value musthave a line of its own at the time of entry. Empty lines are removedautomatically. The number of values will also be definedautomatically on the basis of the available lines. It must be between2 and 20.This function can be used for flexible range definition. Thus, forexample, limits can be defined in the table when a value is normal,suspicious, critical and very critical.Inputs: x: Value in the table (Numerical).Outputs: y: Index of the value / Value range (Numerical).Parameters: p 1 : Table (values table)9.4.11 Characteristic CurveThe Characteristic curve function is used to convert input valuesfrom one range into another. The conversion can be subdivided intovarious segments through the specification of up to 20 nodes.The Table parameter is used to specify the nodes. Each value pairis in a different line in the table. The values for x and y are separatedby a colon. The x values must be listed in ascending order. No xvalue may appear more than once. Empty lines are removedautomatically. The number of values will also be definedautomatically on the basis of the available lines. It must be between2 and 20.The ranges between the nodes are interpolated linearly; the valuesoutside the nodes are extrapolated from the last segment. Alimitation is easy to set up by simply setting another node nearbythat has the same y value. If for example the range of 0 to 450 is tobe converted to percent and at the same time limited to 0 and 100,then this is accomplished with the following value pairs:-1: 00: 0450: 100451: 100Inputs: x: X value of the characteristic curve (Numerical).Outputs: y: Function value from the characteristic curve (Numerical)Parameters: p 1 : Table (values table)Status 2011/08/17 HYDAC ELECTRONIC GMBH Part.-Nr.: 669752
GSM Radio Module CSI-F-10 Page 959.4.12 RampThe Ramp function is used to prevent rapid value changes. Understable conditions, the input value is shown at the output. Changes ofthe input value are however not relayed directly to the output, butonly in small steps instead. Like a slope, so to speak. Differentslopes can be defined for positive and negative value modificationsat the same time.The parameters Falling ramp and Rising ramp are used to specifythe maximum permissible value changes per second.If for example the value 5 is set for Rising ramp and the input valuejumps from 0 to 100, then the output will be only slowly increased,and it will take 20 seconds for the output value to reach 100.Inputs: x: (Numerical)Outputs: y: (Numerical)Parameters: p 1 : Falling ramp (Numerical)p 2 : Rising ramp (Numerical)Status 2011/08/17 HYDAC ELECTRONIC GMBH Part.-Nr.: 669752
Page 1 and 2:
GSM Radio ModuleCSI-F-10User Manual
Page 3 and 4:
GSM Radio Module CSI-F-10 Page 3Tab
Page 5 and 6:
GSM Radio Module CSI-F-10 Page 59.2
Page 7 and 8:
GSM Radio Module CSI-F-10 Page 711.
Page 9 and 10:
GSM Radio Module CSI-F-10 Page 91 G
Page 11 and 12:
GSM Radio Module CSI-F-10 Page 112
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
GSM Radio Module CSI-F-10 Page 21Co
Page 23 and 24:
GSM Radio Module CSI-F-10 Page 23PI
Page 25 and 26:
+U BGNDGSM Radio Module CSI-F-10 Pa
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44: GSM Radio Module CSI-F-10 Page 43
Page 45 and 46: GSM Radio Module CSI-F-10 Page 456.
Page 93: GSM Radio Module CSI-F-10 Page 939.
Page 119 and 120: GSM Radio Module CSI-F-10 Page 119S
show all

CSI-F-10 User manual - Hydac

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?