IntelÃ‚Â® Server System Server System "Emerald Ridge ... - CTL

More documents

Recommendations

Info

Intel® Server System "Emerald Ridge” Integrated Baseboard Management Controller EPSIPMI Command InterfaceParameter NameParameterDescriptionNumberBMC-generated ARP control 10 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0.Gratuitous ARP Interval 11 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0.Default Gateway Address 12 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0.Note: When DHCP is enabled, this parameter is treated as readonly.See Section 4.9.5.1.1 for more information.Default Gateway MAC Address 13 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0Note: The MAC Address will be ignored when setting thisparameter, and invalid when reading. The BMC will use theAddress Resolution Protocol to obtain the target MAC address.Backup Gateway Address 14 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0Backup Gateway MAC Address 15 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0Note: The MAC Address will be ignored when setting thisparameter, and invalid when reading. The BMC will use theAddress Resolution Protocol to obtain the target MAC address.Community String 16 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0Number of Destinations (ReadOnly)17Destination Type 18 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0.Destination type OEM1 (110b) ismapped to SMTP Alerting if supported.Destination Addresses 19 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0Note: Data 8:13 (Alerting MAC Address) will be ignored whensetting this parameter, and invalid when reading. The BMC willuse the Address Resolution Protocol to obtain the target MACaddress.802.1q VLAN ID (12-bit) 20 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0 – not implemented802.1q VLAN Priority 21 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0 – not implementedRCMP+ Messaging Cipher SuiteEntry Support (Read Only)RMCP+ Messaging Cipher SuiteEntries (Read Only)RMCP+ Messaging Cipher SuitePrivilege Levels22 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.023 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.024 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0Destination Address VLAN TAGs 25 Per the Intelligent Platform Management Interface SpecificationSecond Generation v2.0 – not implementedReserved 195 (OEM) ReservedReserved 197 (OEM) ReservedReserved 198 (OEM) ReservedRevision 1.1Intel ® Confidential 103
IPMI Command InterfaceIntel® Server System "Emerald Ridge” Integrated Baseboard Management Controller EPSParameter NameParameterDescriptionNumberDHCP Host Name 199 (OEM) When used in Set LAN Configuration Parameters:Byte 1Block selector (01h – 04h), blocks are each 16 byteslong. This byte is only used in the case of Set LANConfiguration command. In the case of Get LANConfiguration, the set selector in the Get LANConfiguration command will be used and this byte willnot exist as part of the payload.Byte 2Set host-name in-progress indicator[7:1] - reserved[0] - in progress0h = Update in progress.1h = Update is completed with this requestBytes 3-18 (16 bytes)Printable ASCII character string. Total length is 63bytes followed by a null. The ASCII string is split into16 bytes blocks, with each block identified by the blockselector. If a null character is found, the followingcharacters after the null character will be ignored.Response DataByte 10x00 –Successful Completion Code0x80 – Parameter Not Supported (Non-printablehostname)0xCC –For Invalid data field0xC7 – For Invalid data lengthWhen used in Get LAN Configuration Parameters:Byte 1Set Selector always 0Byte 2Block Selector (1-4)Value 0 is ReservedResponse DataByte 10x00 –Successful Completion Code0xCC – For Invalid data field0xC7 – For Invalid data lengthIf Byte 1 is equal to 0 thenByte 3 -Byte 18 contain requested hostname block.104Intel ConfidentialRevision 1.1
Page 1:
Intel ® Server System "Emerald Rid
Page 4 and 5:
錯誤 ! 尚未定義樣式
Page 6 and 7:
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71: Intel® Server System "Emerald Ridg
Page 156 and 157: Intel® Server System "Emerald "Rid
Page 170 and 171:
Intel® Server System "Emerald "Rid
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Intel® Server System "Emerald Ridg
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
show all

IntelÃ‚Â® Server System Server System "Emerald Ridge ... - CTL

Create successful ePaper yourself

Delete template?

Save as template?