IntelÃ‚Â® Server System Server System "Emerald Ridge ... - CTL

More documents

Recommendations

Info

錯誤 ! 尚未定義樣式。 EPSFunctional Specification3.26 Global Fan Fault LEDEmerald Ridge platform has a Fan Fault LED located on front panel next to System Status LED,which indicates Fan Fault on system, since FAN LEDs are inside chassis, user can use thisLED to find out if there are any fan failures in the systemOn normal condition Global Fan Fault LED will be OFF. In case of fan fault (Any of system Fan),addition to relevant FAN fault LED, Global FAN fault LED will be amber solid,Global fan fault LED will be OFF only if NONE of system fan fault LED is ON and Global FanFault LED will be ON only if ANY of Fan fault LED is ON.None of other sensors and System status contributes to Global Fan Fault LEDIn case of fan fault when system is powered off ( DC off), Global Fan fault LED will be ON sothat user can see the fan fault without opening the chassis and it will be turned off till sensor isrearmed ( int agent in case of DC on)3.27 Power Management Bus (PMBus)The BMC firmware implements power-management features based on the Power ManagementBus (PMBus) 1.1 Specification.3.27.1 PMBus AddressingThe power supply device address locations are shown below.Table 13. PMBus Device AddressingPower Supply #Power Supply 1Power Supply 2Power Supply 3Power Supply 4B0hB2hB4hB6hPMBus Address3.27.2 PMBus-specific specific Sensor SupportThe following sensor types are supported for systems that contain PMBus-compliant powersupplies and a PMBus-compliant power distribution board.3.27.2.1 Power Supply Input Power SensorThis analog sensor monitors AC power input to the system.IPMI Sensor CharacteristicsEvent reading type code: 01h (Threshold)Sensor type code: 0Bh (Other Units)Rearm type: AutoConfigured thresholds: Upper critical/non-criticalRevision 1.1Intel ® Confidential 43
錯誤 ! 尚未定義樣式。錯誤 ! 尚未定義樣式。 EPSEvent generation: Assertion/deassertion events for all supported thresholds3.27.2.2 Power Supply Output Current SensorThe BMC supports one Power Supply Output Current sensor for each system power supplymodule. This sensor is only supported for systems that use PMBus-compliant power supplies.The BMC reads current for the main 12 V power rail coming out of the power supply andexpresses the reading as the percentage of max rated output current for the power rail.This monitoring capability is instantiated in the form of IPMI analog/threshold sensors.IPMI Sensor CharacteristicsEvent reading type code: 01h (Threshold)Sensor type code: 03h (Current)Rearm type: AutoConfigured thresholds: Upper critical/non-criticalEvent generation: Assertion/deassertion events for all supported thresholds3.27.2.3 Power Supply Temperature SensorThe BMC supports two Power Supply Temperature sensors for each system power supplymodule. One temperature sensor uses in standby mode, the other uses in active mode. Thestandby sensors would be available only when the system in standby mode, reading for thesesensors in power on state would result in "reading not available" state. The active mode sensorswould be available only when system power on more then 25 seconds due to BMC delays 25seconds after DC Power On to access these sensors. Reading for these sensors in standbystate and power on less then 25 seconds would result in "reading not available" state. Moreover,the standby sensors and active mode sensors have different thresholds.These sensors are only supported with systems that use PMBus-compliant power supplies. Thismonitoring capability is instantiated in the form of IPMI analog/threshold sensors. The location ofthe physical temperature sensor in the power supply helps to provide a measurement of inlet airtemperature to the power supply. These sensors are implemented as auto rearm.3.28 Power Unit ManagementThe BMC supports IPMI type 09h, power unit sensor, using the following offsets:Table 14. Power Unit Sensor OffsetsOffsetDescriptionEvent Logging00h Power off – Asserted whenever the system DC power is off. Assertion andDeassertion04h05hAC lost – Asserted momentarily for event generation when AC power isapplied to the system and the previous system power state was on.Soft power control failure – Asserted if the system fails to power-on due to thefollowing power control sources:Chassis Control commandPEF actionBMC Watchdog TimerPower State RetentionAssertion andDeassertionAssertion andDeassertion44Intel ConfidentialRevision 1.1
Page 1:
Intel ® Server System "Emerald Rid
Page 4 and 5:
錯誤 ! 尚未定義樣式
Page 6 and 7:
Page 8 and 9:
Page 10 and 11: 錯誤 ! 尚未定義樣式
Page 70 and 71: Intel® Server System "Emerald Ridg
Page 110 and 111:
Intel® Server System "Emerald Ridg
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Intel® Server System "Emerald "Rid
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
show all

IntelÃ‚Â® Server System Server System "Emerald Ridge ... - CTL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?