IntelÃ‚Â® Server System Server System "Emerald Ridge ... - CTL

More documents

Recommendations

Info

Intel® Server System "Emerald "Ridge” Integrated Baseboard Management Controller EPS SensorsFull Sensor Name(Sensor name in SDR)BB VCORE CPU3(BB VCORE CPU3)BB VCORE CPU4(BB VCORE CPU4)BB VCACHE CPU3(BB VCACHE CPU3)BB VCACHE CPU4(BB VCACHE CPU4)Sensor #D5hD6hD7hD8hSensor TypeVoltage02hVoltage02hVoltage02hVoltage02hNote : This sensor only available in standby mode.Event t /Reading TypeThreshold01hThreshold01hThreshold01hThreshold01hEvent OffsetTriggers[u,l] [c,nc][u,l] [c,nc][u,l] [c,nc][u,l] [c,nc]Contrib. To SystemStatusnc = Degradedc = Non-fatalnc = Degradedc = Non-fatalnc = Degradedc = Non-fatalnc = Degradedc = Non-fatalAsandDeAsandDeAsandDeReadableEventRearmValue /DataOffsetsAnalog R, T A –Analog R, T A _Analog R, T A –Analog R, T A _Assert/ De-assertAsandDeStand-byRevision 1.0 Intel ® Confidential 153
錯誤 ! 尚未定義樣式。EPS14. Chassis sis ManagementIntel® Server System "Emerald Ridge” Integrated Baseboard Management ControllerThis section provides a description of chassis management support for chassis used withServer Boards that use the Intel ® Chipset.14.1 BMC Chassis ManagementThese elements are common to the Server Chassis used for Server Boards that use the Intel ®Chipset:Power on / off button: Also serves as system shut-down to soft-power off mode (S5)request button under ACPI.System reset button.System identify button: Pressing this button toggles the state of the Chassis ID LED.Chassis ID LED: Provides a way to identify a system to be serviced, or that is in theprocess of being serviced. The LED state toggles when the system identification buttonhas been pressed. It can also be turned on and off by sending commands to the BMC.Diagnostic interrupt: Also known as the control panel NMI. It is a button with hiddenaccess.Power on LED: Also used to indicate system sleep state.System status LED: Indicates normal, degraded, non-critical, and critical conditionsdetected by the system management sub-system.Consolidated drive status LED: Located on the control panel, this LED serves twopurposes. It indicates drive activity and provides an indication when one or more fixeddrives or drives on the hot-swap backplane have a fault condition asserted.Fan Fault LED: Indicates a fan failure. It is associated with each fan. A fan fault LEDlights if the associated fan tach sensor has a lower critical threshold event statusasserted. Fan tach sensors are manual rearm sensors. Once the lower critical thresholdis crossed, the LED remains lit until the sensor is rearmed. These sensors are rearmedat system DC power-on and system reset.Global Fan Fault LED: Located on the control panel, it lights up when one or moresystem fan fault asserted.154Intel ConfidentialRevision 1.1
Page 1:
Intel ® Server System "Emerald Rid
Page 4 and 5:
錯誤 ! 尚未定義樣式
Page 6 and 7:
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Intel® Server System "Emerald Ridg
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121: Intel® Server System "Emerald Ridg
Page 156 and 157: Intel® Server System "Emerald "Rid
Page 172 and 173: 錯誤 ! 尚未定義樣式
show all

IntelÃ‚Â® Server System Server System "Emerald Ridge ... - CTL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?