IntelÃ‚Â® Server System Server System "Emerald Ridge ... - CTL

More documents

Recommendations

Info

Intel® Server System "Emerald Ridge” Integrated Baseboard Management Controller EPSIPMI Command InterfaceSender Email Address *(Max no of Blocks = 4)SMTP Host name *(Max no of Blocks = 2)ParameterParameterParameter DataNumber8 Configure the sender e-mail addressData 1: N: E-mail address String in ASCII, 64 bytesmax.Block size is 16 Bytes.Address with greater than 16 bytes need more thanone set/get SMTP configuration.Names with fewer than 16 bytes are terminatedwith a null (00h) character and 00h padded to theremaining bytes. When the User name is read backthose bytes shall be returned as 0.9 Configure the SMTP host name.Data 1: N: E-mail address String in ASCII, 32 bytesmax.Block size is 16 bytesNames with fewer than 16 bytes are terminatedwith a null (00h) character and 00h padded to theremaining bytes. When the SMTP Host name isread back those padding bytes shall be returned as0.* Set selector is not applicable because these parameters are common for all Alert destinations.Both should be zero.Note: All SMTP alerts are sent to TCP port 25 on the destination machine.10.4 Completion CodesSome commands may implement other completion codes. These are defined in the IntelligentPlatform Management Interface Specification Second Generation v2.0, or if BMC specific, in thecommand tables above.Table 66. IPMI 2.0 Completion CodesCompletion Code00h08hC0hC1hC2hC3hC4hC5hC7hC8hC9hCAhCBhCChMeaningThe command was successfully completed.Used by RAS commands to indicate RAS sensor update is in progress.Node busy. The command could not be processed because command processing resources aretemporarily unavailable.Invalid command. Used to indicate an unrecognized or unsupported command.The command is invalid for the given LUN.Timeout while processing command. A response is not available.Out of space. The command could not be completed because of a lack of storage space requiredto execute the given command operation.The action was not performed due to a canceled or invalid reservation number.The command has the wrong number of data bytes.Too many data bytes for requested operation.One or more of the data bytes in a command is outside the range of valid values.Cannot return the number of requested data bytes.The request is for a nonexistent sensor in the BMCOne or more of the data bytes is an invalid value.Revision 1.1Intel ® Confidential 127
IPMI Command InterfaceIntel® Server System "Emerald Ridge” Integrated Baseboard Management Controller EPSCompletion CodeCDhCEhD0hD1hD3hD4hFFhMeaningThe requested operation is not supported for the given sensor.Command not completed; a BMC peripheral did not respond.Command response could not be provided. SDR Repository in update mode.Command response could not be provided. Device in firmware update mode.Cannot deliver request to selected destination.Cannot execute command. Insufficient privilege level.Unspecified error.10.5 Command SupportThe information in Table 67 through Table 72 specifies the privilege level associated with eachcommand and whether the command is supported in operational and firmware transfer modes.The following restrictions apply to the commands:Only allowed over the system interfaceOnly available over local interface (system interface or IPMB)This section does not list the commands available on the SMM interface.Note: Per the Intelligent Platform Management Interface Specification Second Generation v2.0,unauthenticated, session-less interfaces, such as the system interface and IPMB, can supportany IPMI command unless otherwise specified.Table 67. Command Support Matrix, Network Function = Application – 06hCommand Name Cmd #Operational Mode PrivilegeGet Device ID 01h UserBroadcast Get Device ID 01h User 1Cold Reset 02h AdminGet Self Test Results 04h UserManufacturing Test On 05h AdminSet ACPI Power State 06h AdminGet ACPI Power State 07h UserReset Watchdog Timer 22h OperatorSet Watchdog Timer 24h OperatorGet Watchdog Timer 25h UserSet BMC Global Enables 2Eh Admin 2Get BMC Global Enables 2Fh UserClear Message Flags 30h Admin 2Get Message Flags 31h Admin 2Get Message 33h Admin 2Send Message 34h UserRead Event Message Buffer 35h Admin 2Get System GUID o 37h AnyGet Channel Authentication Capabilities 38h Any128Intel ConfidentialRevision 1.1
Page 1:
Intel ® Server System "Emerald Rid
Page 4 and 5:
錯誤 ! 尚未定義樣式
Page 6 and 7:
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Intel® Server System "Emerald Ridg
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95: Intel® Server System "Emerald Ridg
Page 156 and 157: Intel® Server System "Emerald "Rid
Page 172 and 173: 錯誤 ! 尚未定義樣式
Page 194 and 195:
Page 196 and 197:
show all

IntelÃ‚Â® Server System Server System "Emerald Ridge ... - CTL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?