User Manual High Performance AC Drive

Programming and Parameters 3-105NameNo. Description1109 DelTmr1 Trig BitSelects the bit, from the word linked to Par 1108 [DelTmr1 TrigData], that will change thestatus of the user-defined delay timer to on or off. When Par 1109 [DelTmr1 Trig Bit] is apositive number, the delay timer is an “on” timer. When Par 1109 is a negative number, thedelay timer is an “off” timer.Note: This parameter was added for firmware version 3.01.Default: 0Min/Max: -/+321110 DelayTimer1PrSetUnits: Sec.The time that the value in Par 1111 [DelayTimer1Accum] must reach before bit 2 [Timer Done] Default: 0in Par 1112 [DelayTimer1Stats] is set.Min/Max: 0/600.00Note: This parameter was added for firmware version 3.01.1111 DelayTimer1AccumThe amount of time that has elapsed since the timer was enabled (Par 1112[DelayTimer1Stats], bit 2 set).Note: This parameter was added for firmware version 3.01.1112 DelayTimer1StatsThe status of the user-defined on or off delay timer.Bit 0 [Timer Enable] when this bit is set, the timer is enabled.Bit 1 [Timer Timing] when this bit is set, the timer is running.Bit 2 [Timer Done] when this bit is set, the timer is done.Note: This parameter was added for firmware version 3.01.ValuesUnits: Sec.Default: 0Min/Max: 0/600.00LinkableRead-WriteData Type✓RW 16-bitIntegerRW 16-bitIntegerRO 16-bitIntegerOptionsReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedTimer DoneTimer TimingTimer EnableDefault 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 01113 DelTmr2 TrigDataDefault: 0Link a word to this parameter that will control a user-defined on or off delay timer. The bit Min/Max: 32 bits of datawithin the selected word that will control the delay timer is set by Par 1114 [DelTmr2 Trig Bit].The user-defined on/off delay timer is enabled by setting bit 6 [Delay Timer] of Par 1000[UserFunct Enable].DelayTimer2PrSetDelayTimer2 Data11151113DelayTimer2Stats 00 Enabled1117 00 TimingDelayTimer 200 DoneDelayTimer2 Bit 11141116 DelayTimer2AccumNote: This parameter was added for firmware version 3.01.1114 DelTmr2 Trig BitSelects the bit, from the word linked to Par 1113 [DelTmr2 TrigData], that will change thestatus of the user-defined delay timer to on or off. When Par 1114 [DelTmr2 Trig Bit] is apositive number, the delay timer is an “on” timer. When Par 1114 is a negative number, thedelay timer is an “off” timer.Note: This parameter was added for firmware version 3.01.Default: 0Min/Max: -/+321115 DelayTimer2PrSetUnits: Sec.The time that the value in Par 1116 [DelayTimer2Accum] must reach before bit 2 [Timer Done] Default: 0in Par 1117 [DelayTimer2Stats] is set.Min/Max: 0/60000Note: This parameter was added for firmware version 3.01.1116 DelayTimer2AccumThe amount of time that has elapsed since the timer was enabled (Par 1117[DelayTimer2Stats], bit 1 set).Note: This parameter was added for firmware version 3.01.1117 DelayTimer2StatsThe status of the user-defined on or off delay timer.Bit 0 [Timer Enable] when this bit is set, the timer is enabled.Bit 1 [Timer Timing] when this bit is set, the timer is running.Bit 2 [Timer Done] when this bit is set, the timer is done.Note: This parameter was added for firmware version 3.01.OptionsReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedTimer DoneTimer TimingTimer EnableDefault 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 00 = False1 = True0 = False1 = TrueUnits: Sec.Default: 0Min/Max: 0/60000✓▲✓RW 32-bitBooleanRW 16-bitIntegerRW 16-bitIntegerRO 16-bitInteger